Cisco Systems CGS252016S8PC manual Power Supply Side, SD Flash Memory Card, Color

Page 19

Chapter 1 Product Overview

Power Supply Side

Table 1-10 SD Flash Memory Card LED (continued)

Color

Amber

Green

System Status

Error accessing the SD flash memory card; Cisco IOS boot image cannot be found

SD flash memory card is functioning

SD Flash Memory Card

The switch ships with the Secure Digital (SD) flash memory card installed. See Figure 1-1and

Figure 1-2. You can remove the card from a failed switch and install it in a replacement switch. You do not have to reconfigure the new switch. See the Replacing the SD Flash Memory Card, page 2-22for information.

Warning Be aware that the SD card contains sensitive and security relevant information, including but not limited to full device configuration information, public and private keys used for SSH and SSL (if those protocols are enabled), device passwords and others. Access to SD cards for any Cisco CGS switch should be limited to authorized personnel.

Power Supply Side

The power supply side has the LED panel and two power supply slots for the removable power supplies. See Figure 1-7and Figure 1-8.

Figure 1-7 Switch with One Power Supply Module

Cisco

 

 

Connected

Grid

Switch

 

 

2500 Series

1

PWR-RGD-LOW-DC

2

207200

3

1

LED panel

Power supply slot 1

3

Power supply slot 2

Cisco CGS 2520 Hardware Installation Guide

 

78-19377-02

1-11

 

 

 

Image 19
Contents Americas Headquarters Cisco CGS 2520 Hardware Installation GuideCisco CGS 2520 Hardware Installation Guide N T E N T S Wall-Mounting Bad or Damaged Cable USB Console Port Preface Related Publications Obtaining Documentation and Submitting a Service RequestModel Description Switch ModelsCisco CGS-2520-24TC Cable-Side View Cable SidePoE Ports 10/100 Fast Ethernet PortsSFP Modules Dual-Purpose PortsType of SFP Module Model SFP Module Patch CableAlarm Output Power-Input TerminalAlarm Ports Alarm InputUSB Mini-Type B Port LEDsSystem LED Switch Panel LEDsColor System Status Color Description Power Supply Module LEDsAlarm LEDs Console LEDsSD Flash Memory Card LED Port LEDsPoE LED Dual-Purpose Port LEDsSD Flash Memory Card Power Supply SideColor USB LED Power Supply-Side LEDsManagement Options Power Supply FeaturesNetwork Configurations Switch Installation 140F 60C Statement Verifying Switch Operation Installation Guidelines75 in .4 cm. Statement Mounting into a Rack Installing the SwitchMounting Brackets 2shows the 23-inch rack mounting brackets Attaching Brackets for 19-Inch RacksAttaching Brackets for 19-Inch Racks Attaching Brackets for 19-Inch Racks IP-30 Compliance Inserting the Rubber Plugs Inserting the Rubber Plugs Inserting the Rubber Plugs detail Attaching Brackets for 19-Inch Racks 10 Attaching Brackets for 19-Inch Racks Attaching Brackets for 23-Inch Racks11 Attaching Brackets for 23-Inch Racks Attaching Brackets for Etsi Racks12 Attaching Brackets for Etsi Racks Mounting the Switch into a Rack Attaching Brackets for Wall Mounting Wall-Mounting14 Attaching 19-inch Rack Brackets for Wall Mounting Wall-Mounting for IP-30 Compliance15 Inserting the Rubber Plugs into the Switch Holes Installing SFP Modules Installing and Removing SFP ModulesRemoving SFP Modules 17 Installing an SFP Module18 Removing a Bale Clasp Latch SFP Module Inserting and Removing the SFP Module Patch CableRemoving the SFP Module Patch Cable Replacing the SD Flash Memory Card21 Loosening the Captive Screw Device Crossover Cable Straight-Through Cable Connecting Devices to the Ethernet PortsConnecting to the 10/100 PoE Ports Connecting to the 10/100 and 10/100/1000 PortsWhere to Go Next Power Supply Modules Power Supply InstallationPWR-RGD-AC-DC Power Supply Module Power Supply Module InstallationInstalling a Power Supply Module Installation GuidelinesEquipment That You Need Grounding the Switch Dual-hole terminal lug Loosen the Screws on the Power Supply Blank Installing the Power Supply Module in the SwitchAC 5 A, DC 15 a Statement Wiring the Power SourcePSU2 11 Stripping the Input Power Source Wire AC power connection DC power connection 15 Removing the Screws Removing the Power Supply Module78-19377-02 Page Switch Post Results Diagnosing ProblemsSwitch LEDs Link Status Switch ConnectionsBad or Damaged Cable Ethernet and Fiber-Optic CablesPing End Device Interface Settings10/100 PoE Port Connections SFP ModuleAuto-Negotiation and Network Interface Cards Switch PerformanceSpanning Tree Loops Speed, Duplex, and Auto-NegotiationFinding the Switch Serial Number Resetting the Switch to the Factory Default SettingsPage Physical Specifications Switch SpecificationsEnvironmental Ranges Power Requirements Power Requirements Power Specifications Power Supply Module Specifications10/100 Ethernet Ports Connector SpecificationsFigure B-2 Fiber-Optic SFP Module LC Connector SFP Module ConnectorsAlarm Ratings Alarm PortCommercial SFPs Cables and AdaptersSFP Module Cables Industrial and Rugged SFPs100BASE-BX Cable Pinouts Extended temperature SFPsFigure B-6 Console Port Adapter Pinouts Switch Console RJ-45-to-DB-9Port DTE Terminal Adapter Device Switch Console RJ-45-to-DB-25 Port DTE Adapter Device Page RJ-45 Console Port Accessing the CLI Through the Console PortFigure C-1 Connecting the Console Cable USB Console Port Figure C-2 Connecting the USB Console CableInstalling the Cisco Microsoft Windows XP USB Driver Installing the Cisco Microsoft Windows USB Device DriversInstalling the Cisco Microsoft Windows 2000 USB Driver Installing the Cisco Microsoft Windows Vista USB Driver Uninstalling the Cisco Microsoft Windows USB DriversIP Settings Entering the Initial Configuration InformationUninstalling the Cisco Microsoft Windows Vista USB Driver Completing the Setup Program These choices appear Numerics IN-2 IN-3 IN-4