Cisco Systems CGS252016S8PC manual Figure C-1 Connecting the Console Cable

Page 84

Appendix C Configuring the Switch with the CLI Setup Program

Accessing the CLI Through the Console Port

Figure C-1 Connecting the Console Cable

1

2

1

1

						207536
						207536
RJ-45 console port		2		Console cable (RJ-45-to-DB-9 adapter cable)
RJ-45 console port		2		Console cable (RJ-45-to-DB-9 adapter cable)

Step 3 Configure the baud rate and character format of the PC or terminal to match the console port characteristics:

•9600 baud

•8 data bits

•1 stop bit

•No parity

•None (flow control)

Step 4 Connect power to the switch as described in Power Supply Installation, page 3-1

Step 5 The PC or terminal displays the bootloader sequence. Press Enter to display the setup prompt. Follow the steps in the Completing the Setup Program, page C-7.

Cisco CGS 2520 Hardware Installation Guide

	C-2	78-19377-02

Image 84

Contents Cisco CGS 2520 Hardware Installation Guide Americas HeadquartersCisco CGS 2520 Hardware Installation Guide N T E N T S Wall-Mounting Bad or Damaged Cable USB Console Port Preface Obtaining Documentation and Submitting a Service Request Related PublicationsSwitch Models Model DescriptionCable Side Cisco CGS-2520-24TC Cable-Side View10/100 Fast Ethernet Ports PoE PortsDual-Purpose Ports SFP ModulesSFP Module Patch Cable Type of SFP Module ModelPower-Input Terminal Alarm PortsAlarm Input Alarm OutputLEDs USB Mini-Type B PortSwitch Panel LEDs System LEDColor System Status Power Supply Module LEDs Alarm LEDsConsole LEDs Color DescriptionPort LEDs PoE LEDDual-Purpose Port LEDs SD Flash Memory Card LEDPower Supply Side SD Flash Memory CardColor Power Supply-Side LEDs USB LEDPower Supply Features Management OptionsNetwork Configurations Switch Installation 140F 60C Statement Installation Guidelines Verifying Switch Operation75 in .4 cm. Statement Installing the Switch Mounting into a RackMounting Brackets Attaching Brackets for 19-Inch Racks 2shows the 23-inch rack mounting bracketsAttaching Brackets for 19-Inch Racks Attaching Brackets for 19-Inch Racks IP-30 Compliance Inserting the Rubber Plugs Inserting the Rubber Plugs Inserting the Rubber Plugs detail Attaching Brackets for 19-Inch Racks Attaching Brackets for 23-Inch Racks 10 Attaching Brackets for 19-Inch RacksAttaching Brackets for Etsi Racks 11 Attaching Brackets for 23-Inch Racks12 Attaching Brackets for Etsi Racks Mounting the Switch into a Rack Wall-Mounting Attaching Brackets for Wall MountingWall-Mounting for IP-30 Compliance 14 Attaching 19-inch Rack Brackets for Wall Mounting15 Inserting the Rubber Plugs into the Switch Holes Installing and Removing SFP Modules Installing SFP Modules17 Installing an SFP Module Removing SFP ModulesInserting and Removing the SFP Module Patch Cable 18 Removing a Bale Clasp Latch SFP ModuleReplacing the SD Flash Memory Card Removing the SFP Module Patch Cable21 Loosening the Captive Screw Connecting Devices to the Ethernet Ports Device Crossover Cable Straight-Through CableConnecting to the 10/100 and 10/100/1000 Ports Connecting to the 10/100 PoE PortsWhere to Go Next Power Supply Installation Power Supply ModulesPower Supply Module Installation PWR-RGD-AC-DC Power Supply ModuleInstallation Guidelines Installing a Power Supply ModuleEquipment That You Need Grounding the Switch Dual-hole terminal lug Installing the Power Supply Module in the Switch Loosen the Screws on the Power Supply BlankWiring the Power Source AC 5 A, DC 15 a StatementPSU2 11 Stripping the Input Power Source Wire AC power connection DC power connection Removing the Power Supply Module 15 Removing the Screws78-19377-02 Page Diagnosing Problems Switch Post ResultsSwitch LEDs Switch Connections Bad or Damaged CableEthernet and Fiber-Optic Cables Link StatusInterface Settings 10/100 PoE Port ConnectionsSFP Module Ping End DeviceSwitch Performance Spanning Tree LoopsSpeed, Duplex, and Auto-Negotiation Auto-Negotiation and Network Interface CardsResetting the Switch to the Factory Default Settings Finding the Switch Serial NumberPage Switch Specifications Physical SpecificationsEnvironmental Ranges Power Requirements Power Requirements Power Supply Module Specifications Power SpecificationsConnector Specifications 10/100 Ethernet PortsSFP Module Connectors Figure B-2 Fiber-Optic SFP Module LC ConnectorAlarm Port Alarm RatingsCables and Adapters SFP Module CablesIndustrial and Rugged SFPs Commercial SFPs100BASE-BX Extended temperature SFPs Cable PinoutsFigure B-6 Switch Console RJ-45-to-DB-9 Console Port Adapter PinoutsPort DTE Terminal Adapter Device Switch Console RJ-45-to-DB-25 Port DTE Adapter Device Page Accessing the CLI Through the Console Port RJ-45 Console PortFigure C-1 Connecting the Console Cable Figure C-2 Connecting the USB Console Cable USB Console PortInstalling the Cisco Microsoft Windows USB Device Drivers Installing the Cisco Microsoft Windows XP USB DriverInstalling the Cisco Microsoft Windows 2000 USB Driver Uninstalling the Cisco Microsoft Windows USB Drivers Installing the Cisco Microsoft Windows Vista USB DriverEntering the Initial Configuration Information IP SettingsUninstalling the Cisco Microsoft Windows Vista USB Driver Completing the Setup Program These choices appear Numerics IN-2 IN-3 IN-4