Cisco Systems 3650 manual OL-29734-01

Page 26

Chapter 2 Switch Installation

Preparing for Installation

Warning Ethernet cables must be shielded when used in a central office environment. Statement 171

Warning Voice over IP (VoIP) service and the emergency calling service do not function if power fails or is disrupted. After power is restored, you might have to reset or reconfigure equipment to regain access to VoIP and the emergency calling service. In the USA, this emergency number is 911. You need to be aware of the emergency number in your country. Statement 361

Warning Do not work on the system or connect or disconnect cables during periods of lightning activity. Statement 1001

Warning Read the installation instructions before connecting the system to the power source. Statement 1004

Warning This unit is intended for installation in restricted access areas. A restricted access area can be accessed only through the use of a special tool, lock and key, or other means of security. Statement 1017

Warning The plug-socket combination must be accessible at all times, because it serves as the main disconnecting device. Statement 1019

Warning Use copper conductors only. Statement 1025

Warning This unit might have more than one power supply connection. All connections must be removed to de-energize the unit. Statement 1028

Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030

Warning Ultimate disposal of this product should be handled according to all national laws and regulations. Statement 1040

Warning For connections outside the building where the equipment is installed, the following ports must be connected through an approved network termination unit with integral circuit protection: 10/100/1000 Ethernet. Statement 1044

Catalyst 3650 Switch Hardware Installation Guide

2-2

OL-29734-01

 

 

Image 26
Contents Document Conventions PrefacePurpose Obtaining Documentation and Submitting a Service Request Related DocumentationProduct Overview Switch ModelsSwitch Model Cisco IOS Image Description Product Overview Switch Models Switch Model Cisco IOS Image Description Front Panel Catalyst 3650-48PD-L Switch Front Panel Management Ports 10/100/1000 Ethernet PortsPoE and PoE+ USB Type a Port USB Mini-Type B PortSFP and SFP+ Modules Uplink PortsLEDs 3 4 5 Color System StatusMode LED Port Mode Description Port LEDs and ModesPort Mode Port LED Color Meaning USB Console LED ColorPoE+ LED Color DescriptionUplink Ports LEDs Color PoE+ StatusRear Panel Color Uplink Ports Link StatusRJ-45 Console Port Status1 RJ-45 Console Port LEDStackWise Ports Power Supply Modules AC-Power Supply Module LEDs Models Default Power Supply Available PoE PowerPoE Option Port Switch ModelsDC-Power Supply Module LEDs Fan ModulesRJ-45 Console Port Management OptionsEthernet Management Port Network Configurations OL-29734-01 Safety Warnings Switch InstallationPreparing for Installation OL-29734-01 Installation Guidelines Powering Off the Switch Planning a Switch Data StackVerifying Switch Operation Tools and EquipmentSwitch Stacking Guidelines Data Stack Cabling ConfigurationsData Stacking up to Four Switches in a Side-by-Side Mounting Data Stack Bandwidth and Partitioning ExamplesPower-On Sequence for Switch Data Stacks Example of a Data Stack with Half Bandwidth ConnectionsChanges to Switch Stack Membership Installing the Switch Rack-Mounting Attaching the Rack-Mount Brackets Rack-Mounting BracketsAttaching Brackets for 19-inch Racks Mounting the Switch in a Rack Mounting the Switch in a RackAfter Installing the Switch Table- or Shelf-MountingConnecting to the StackWise Ports Installing the StackWise Adapter in a StackWise Port Installing and Removing SFP and SFP+ Modules Installing SFP and SFP+ Modules14 Installing an SFP Module in an Uplink Port 10/100/1000 Ethernet Port Connections Connecting Devices to the Ethernet PortsRemoving SFP or SFP+ Modules Switch Installation Connecting Devices to the Ethernet Ports PoE+ Port Connections Device Crossover CableWhere to Go Next Part Number Description Power Supply InstallationPower Supply Module Overview AC OK LED 640-W AC Power Supply Module 6 5 DC Power Supply Module LEDs Installation GuidelinesAC Power Supply Module LEDs Installing or Replacing an AC Power Supply Installing a DC Power Supply StatementGrounding the Switch Equipment That You NeedStripping the Ground Wire 10 Attaching the Ground Lug and Wire Assembly Installing the DC Power Supply in the Switch Wiring the DC Input Power SourceFinding the Power Supply Module Serial Number 12 DC Source a Isolated From Source B with No Common Ground14 1025-W AC Power Supply Serial Number 16 640-W DC Power Supply Module Serial Number Installing the Fan OverviewFan Module Installation Installing a Fan Module Fan LEDFinding the Fan Module Serial Number Fan Module Serial NumberSwitch Post Results TroubleshootingDiagnosing Problems Switch LEDsEthernet and Fiber Cables Switch ConnectionsBad or Damaged Cable Link StatusSFP Modules 10/100/1000 Port ConnectionsPoE and PoE+ Port Connections Ping End Device Switch PerformanceInterface Settings Spanning Tree LoopsCabling Distance Resetting the SwitchAutonegotiation and Network Interface Cards Finding the Switch Serial Number Replacing a Failed Data Stack MemberEnvironmental Ranges Technical SpecificationsSwitch Specifications Physical Specifications Power Supply Module Specifications Power SpecificationsPower Specifications Operating Specification Fan Module SpecificationsPhysical Specification OL-29734-01 10/100/1000 Ports Connector and Cable SpecificationsConnector Specifications Gigabit Ethernet CX1 SFP+ Copper Connectors SFP and SFP+ ModulesFigure B-4 Simplex LC Cable Connector 10/100/1000 Ethernet Management PortConsole Port Figure B-7 10/100 Port PinoutsCable and Adapter Specifications StackWise CablesLocating the StackWise Adapter Serial Number StackWise AdaptersStackWise Cables Minimum Bend Radius and Coiled Diameter Cable Part Number Cable Length Minimum Bend RadiusSFP and SFP+ Module Cable Specifications StackWise Adapter BlanksFour Twisted-Pair Cable Pinouts Two Twisted-Pair Cable PinoutsConsole Port Adapter Pinouts Switch Console RJ-45-to-DB-9 Port DTEIdentifying a Crossover Cable DeviceSwitch Console RJ-45-to-DB-25 Port DTE DSR DTR CTS RTSAccessing the CLI Through Express Setup Configuring the Switch with the CLI-Based Setup ProgramAccessing the CLI Accessing the CLI Through a Console PortUSB Console Port Installing the Cisco Microsoft Windows USB Device Driver Uninstalling the Cisco Microsoft Windows USB Driver Uninstalling the Cisco Microsoft Windows XP USB DriverConfiguring the Setup Program Entering the Initial Configuration InformationIP Settings Enter a host name for the switch, and press Return These choices appear OL-29734-01