Cisco Systems 3650 manual Installing the Switch

Page 33

Chapter 2 Switch Installation

Installing the Switch

Note Make sure that you power off the switches that you add to or remove from the switch stack.

After adding or removing stack members, make sure that the switch stack is operating at full bandwidth. Press the Mode button on a stack member until the Stack mode LED is on. The last two right port LEDs on all switches in the stack should be green. Depending on the switch model, the last two right ports are 10-Gigabit Ethernet ports or small form-factor pluggable (SFP) module ports (10/100/1000 ports). If one or both of these LEDs are not green on any of the switches, the stack is not operating at full bandwidth.

If you remove powered-on members but do not want to partition the stack:

•Power off the switches in the newly created switch stacks.

•Reconnect them to the original switch stack through their stack ports.

•Power on the switches.

Installing the Switch

•Rack-Mounting, page 2-10

•Table- or Shelf-Mounting, page 2-14

•After Installing the Switch, page 2-14

The illustrations shown in this section show the Catalyst 3650-48 PoE+ switch as an example. You can install other Catalyst 3650 switches following the same procedures.

Catalyst 3650 Switch Hardware Installation Guide

	OL-29734-01	2-9

Image 33

Contents Preface PurposeDocument Conventions Related Documentation Obtaining Documentation and Submitting a Service RequestSwitch Models Switch Model Cisco IOS Image DescriptionProduct Overview Product Overview Switch Models Switch Model Cisco IOS Image Description Front Panel Catalyst 3650-48PD-L Switch Front Panel 10/100/1000 Ethernet Ports PoE and PoE+Management Ports USB Mini-Type B Port USB Type a PortUplink Ports LEDsSFP and SFP+ Modules Color System Status 3 4 5Port LEDs and Modes Mode LED Port Mode DescriptionPort Mode Port LED Color Meaning Color USB Console LEDColor Description PoE+ LEDColor PoE+ Status Uplink Ports LEDsColor Uplink Ports Link Status Rear PanelRJ-45 Console Port LED StackWise PortsRJ-45 Console Port Status1 Power Supply Modules PoE Option Port Switch Models Default Power Supply Available PoE PowerAC-Power Supply Module LEDs ModelsFan Modules DC-Power Supply Module LEDsManagement Options Ethernet Management PortRJ-45 Console Port Network Configurations OL-29734-01 Switch Installation Preparing for InstallationSafety Warnings OL-29734-01 Installation Guidelines Verifying Switch Operation Planning a Switch Data StackPowering Off the Switch Tools and EquipmentData Stack Cabling Configurations Switch Stacking GuidelinesData Stack Bandwidth and Partitioning Examples Data Stacking up to Four Switches in a Side-by-Side MountingExample of a Data Stack with Half Bandwidth Connections Power-On Sequence for Switch Data StacksChanges to Switch Stack Membership Installing the Switch Rack-Mounting Rack-Mounting Brackets Attaching the Rack-Mount BracketsAttaching Brackets for 19-inch Racks Mounting the Switch in a Rack Mounting the Switch in a RackTable- or Shelf-Mounting After Installing the SwitchConnecting to the StackWise Ports Installing the StackWise Adapter in a StackWise Port Installing SFP and SFP+ Modules Installing and Removing SFP and SFP+ Modules14 Installing an SFP Module in an Uplink Port Connecting Devices to the Ethernet Ports Removing SFP or SFP+ Modules10/100/1000 Ethernet Port Connections Switch Installation Connecting Devices to the Ethernet Ports Device Crossover Cable PoE+ Port ConnectionsWhere to Go Next Power Supply Installation Power Supply Module OverviewPart Number Description AC OK LED 640-W AC Power Supply Module 6 5 Installation Guidelines AC Power Supply Module LEDsDC Power Supply Module LEDs Installing or Replacing an AC Power Supply Statement Installing a DC Power SupplyEquipment That You Need Grounding the SwitchStripping the Ground Wire 10 Attaching the Ground Lug and Wire Assembly Wiring the DC Input Power Source Installing the DC Power Supply in the Switch12 DC Source a Isolated From Source B with No Common Ground Finding the Power Supply Module Serial Number14 1025-W AC Power Supply Serial Number 16 640-W DC Power Supply Module Serial Number Overview Installing the FanFan Module Installation Fan LED Installing a Fan ModuleFan Module Serial Number Finding the Fan Module Serial NumberDiagnosing Problems TroubleshootingSwitch Post Results Switch LEDsBad or Damaged Cable Switch ConnectionsEthernet and Fiber Cables Link Status10/100/1000 Port Connections PoE and PoE+ Port ConnectionsSFP Modules Interface Settings Switch PerformancePing End Device Spanning Tree LoopsResetting the Switch Autonegotiation and Network Interface CardsCabling Distance Replacing a Failed Data Stack Member Finding the Switch Serial NumberTechnical Specifications Switch SpecificationsEnvironmental Ranges Physical Specifications Power Specifications Power Supply Module SpecificationsPower Specifications Fan Module Specifications Physical SpecificationOperating Specification OL-29734-01 Connector and Cable Specifications Connector Specifications10/100/1000 Ports SFP and SFP+ Modules Gigabit Ethernet CX1 SFP+ Copper Connectors10/100/1000 Ethernet Management Port Figure B-4 Simplex LC Cable ConnectorFigure B-7 10/100 Port Pinouts Console PortStackWise Cables Cable and Adapter SpecificationsStackWise Cables Minimum Bend Radius and Coiled Diameter StackWise AdaptersLocating the StackWise Adapter Serial Number Cable Part Number Cable Length Minimum Bend RadiusStackWise Adapter Blanks SFP and SFP+ Module Cable SpecificationsTwo Twisted-Pair Cable Pinouts Four Twisted-Pair Cable PinoutsIdentifying a Crossover Cable Switch Console RJ-45-to-DB-9 Port DTEConsole Port Adapter Pinouts DeviceDSR DTR CTS RTS Switch Console RJ-45-to-DB-25 Port DTEAccessing the CLI Configuring the Switch with the CLI-Based Setup ProgramAccessing the CLI Through Express Setup Accessing the CLI Through a Console PortUSB Console Port Installing the Cisco Microsoft Windows USB Device Driver Uninstalling the Cisco Microsoft Windows XP USB Driver Uninstalling the Cisco Microsoft Windows USB DriverEntering the Initial Configuration Information IP SettingsConfiguring the Setup Program Enter a host name for the switch, and press Return These choices appear OL-29734-01