Cisco Systems SLM248G4PS, SLM224G4PS manual System Information, Management Settings

Page 17

Chapter 4

Configuration Using the Console Interface

System Information

From the System Information screen you can check current firmware versions and other general switch information.

System Information

Versions

The Versions screen displays version-related information for each switch in the system.

Versions

Unit The unit number of the switch, from 1 to 6. Status The status of the switch, either master or slave. Software Version The version number of the software . Boot Version The version number of the boot file. Hardware Version The Switch’s current hardware setup.

General System Information

The General System Information screen displays the System Description, System UpTime, System MAC Address, System Contact, System Name and System Location.

General System Information

Management Settings

The Management Settings screen displays the Serial Port Configuration option.

Management Settings

Serial Port Configuration

The Serial Port Configuration screen displays the current baud rate setting. To change the baud rate, select Edit, then use the spacebar to toggle through the different baud rates. Use the Save action to set the new baud rate.

Serial Port Configuration

24/48-Port 10/100 + 4-Port Gigabit Smart Switch with Resilient Clustering Technology and PoE

11

Image 17

Contents Port or 48-Port 10/100 + About This Guide About This GuideIcon Descriptions Online ResourcesTable of Contents Snmp Global Parameters Snmp Views Snmp Group Profile SnmpGigabit Ethernet Fiber Optic Cabling Appendix B About Switch StackingAppendix G Contact Information Appendix C Glossary Appendix D SpecificationsIntroduction ChapterChapter Product Overview Switch LEDs and ports are located on the front panelProduct Overview Front PanelBack Panel Power The Power port is where you connect the AC powerSwitch’s LEDs and ports are located on the front panel Product Overview Installation Chapter InstallationPre-Installation Considerations Placement OptionsRack-Mount Placement Hardware InstallationDesktop Placement To set up a stack with six switches, follow these steps Uplinking the SwitchConfiguring Stack Mode Connect port G1 on Unit 3 to port G2 on Unit Power off the new unit 5 the former master unitConnect port G1 on Unit 2 to port G2 on Unit Login screen appears. Proceed to the Login section below Chapter Configuration Using Console InterfaceUsing telnet Login How to Use the Console InterfaceSwitch Main Menu System Configuration MenuSystem Information Management SettingsIP Configuration User & Password SettingsSecurity Settings Http Reboot System Restore System Default SettingsStack Configuration File ManagementPort Status Menu Port ConfigurationPoE Settings System ModeHelp LogoutSetup Chapter Configuration Using Web-based UtilitySetup Summary Device InformationSetup Network Settings Setup ZoomOrange The administrator has closed down this port Clicking on a port displays the Port Configuration screenSet Time Setup TimeLocal Time Daylight SavingPort Management Port Settings Setup Stack ManagementPort Management Sntp ServersPort Management Port Settings Port Configuration Port Management Link Aggregation LAG ConfigurationPort Management Lacp Port Management PoE Power SettingsVlan Management Vlan Management Port SettingVlan Management Create Vlan Vlan TableJoin Vlan to Port Vlan Management Port to VlanVlan Management Vlan to Port Statistics Rmon History StatisticsStatistics Rmon Statistics Rmon History Table Rmon HistoryLog Table Alarm Table Statistics Rmon AlarmsAdd Alarm Statistics Interface Statistics Statistics Rmon EventsStatistics Port Utilization Security Security 802.1x SettingsEthernet-like ParametersSecurity Port Security Setting TimerSecurity Storm Control Security Management Access ListBroadcast Only Counts only Broadcast traffic QoSSecurity Radius QoS Queue Settings QoS CoS SettingsCoS Settings CoS DefaultQoS Bandwidth QoS Dscp SettingsQoS Basic Mode Spanning Tree Global SettingSpanning Tree STP Status Spanning Tree Global STPSpeed Displays the speed at which the port is operating Spanning Tree STP Port SettingsBridge Settings Multicast Vlan Igmp SettingsMulticast Igmp Snooping Multicast Bridge MulticastSnmp Global Parameters Multicast Bridge Multicast Forward AllSnmp Group Profile Snmp ViewsUser Name Provides a user-defined local user list Snmp Group MembershipSnmp Communities Snmp Notification Recipient Snmp Notification FilterBase Table Advanced TableAdmin User Authentication AdminUser Authentication Local User EditSecure The entry is defined for locked ports Admin Static AddressAdmin Dynamic Address Admin Cable Test Admin Port MirroringQuery Clear Table If selected, this clears the MAC Address tableAdmin Save Configuration Admin Factory Default Admin Firmware UpgradeAdmin Reboot Admin Memory Logs Admin LoggingAdmin Server Logs Logout Admin Flash LogsAppendix a About Gigabit Ethernet Fiber Optic Cabling Appendix aGigabit Ethernet Fiber Optic CablingAbout Switch Stacking Appendix B About Switch StackingAppendix B Stack Building Quick StartStack Resiliency Advanced StackingUnit IDs Unit ID AllocationMaster Election Stack Units Startup ProcessMaster Discovery User Controls Unit and Port ConfigurationStacking Examples Replacing a Failed Stack Member in a Running StackStack Master Failure and Replacement Splitting a Stack Subgroup Contains Both Master Unit and Backup Master UnitBoth Stacks Kept Running During Insertion Merging Two StacksInserting Too Many Units Stacking Cable FailureGlossary Appendix CAppendix C Glossary Glossary Mail protocol on the Internet Packet a unit of data sent over a networkAppendix C Appendix D Appendix D SpecificationsSpecifications Power in compliance with Ieee Class of Service Port-based 802.1p Vlan priority-basedDimensions Management VlanObtaining Warranty Service Warranty InformationAppendix E Exclusions and LimitationsTechnical Support Warranty InformationRegulatory Information Appendix FRegulatory Information Appendix F Norsk Norwegian Miljøinformasjon for kunder i EU Appendix F Contact Information Appendix G