Cisco Systems SLM248G4PS, SLM224G4PS manual Port Status Menu, Port Configuration

Page 21

Chapter 4

Configuration Using the Console Interface

Unit The unit number of the switch, from 1 to 6. MAC Address The MAC address of the switch.

Software The version number of the software that runs the switch.

Uplink The ID number of the switch that has an uplink connection to this switch.

Downlink The ID number of the switch that has a downlink connection from this switch.

Status The status of the switch, either master or slave.

ID After Reset The ID number that the Switch will have after the next system reset. Values are Auto or 1 to 6.

Back to Main Menu

Select Back to Main Menu to exit the System Configuration Menu and return to the Main Menu screen.

Port Status Menu

The Port Status Menu displays three options: Port Status, PoE Status, and Back to Main Menu.

Port Status Menu

Port Status

The Port Status screen displays the following status information for each of the switch’s ports: port number, port status, link status, speed and duplex mode, and flow control status. This screen is read-only; to change a port’s settings, use the Port Configuration screen.

PoE Status

The PoE Status screen displays the following status information for each of the switch’s PoE ports: port number, port status, power allocation, and power consumption. This screen is read-only; to change a port’s PoE settings, use the Port Configuration screen.

PoE Status

Port Configuration

The Port Configuration Menu displays three options: Port Settings, PoE Settings, and Back to Main Menu.

Port Configuration Menu

Port Configuration

The Port Configuration screen allows you to change a port’s settings. You can enable or disable a port, or set its auto-negotiation status, speed and duplex mode, and flow control status.

Port Status

Port Configuration

24/48-Port 10/100 + 4-Port Gigabit Smart Switch with Resilient Clustering Technology and PoE

15

Image 21

Contents Port or 48-Port 10/100 + About This Guide About This GuideIcon Descriptions Online ResourcesTable of Contents Snmp Global Parameters Snmp Views Snmp Group Profile SnmpGigabit Ethernet Fiber Optic Cabling Appendix B About Switch StackingAppendix G Contact Information Appendix C Glossary Appendix D SpecificationsIntroduction ChapterChapter Product Overview Switch LEDs and ports are located on the front panelProduct Overview Front PanelPower The Power port is where you connect the AC power Switch’s LEDs and ports are located on the front panelBack Panel Product Overview Installation Chapter InstallationPre-Installation Considerations Placement OptionsHardware Installation Desktop PlacementRack-Mount Placement Uplinking the Switch Configuring Stack ModeTo set up a stack with six switches, follow these steps Power off the new unit 5 the former master unit Connect port G1 on Unit 2 to port G2 on UnitConnect port G1 on Unit 3 to port G2 on Unit Chapter Configuration Using Console Interface Using telnetLogin screen appears. Proceed to the Login section below Login How to Use the Console InterfaceSwitch Main Menu System Configuration MenuSystem Information Management SettingsUser & Password Settings Security SettingsIP Configuration Http Reboot System Restore System Default SettingsStack Configuration File ManagementPort Status Menu Port ConfigurationPoE Settings System ModeHelp LogoutSetup Chapter Configuration Using Web-based UtilitySetup Summary Device InformationSetup Network Settings Setup ZoomOrange The administrator has closed down this port Clicking on a port displays the Port Configuration screenSet Time Setup TimeLocal Time Daylight SavingPort Management Port Settings Setup Stack ManagementPort Management Sntp ServersPort Management Port Settings Port Configuration Port Management Link Aggregation LAG ConfigurationPort Management Lacp Port Management PoE Power SettingsVlan Management Vlan Management Port SettingVlan Management Create Vlan Vlan TableVlan Management Port to Vlan Vlan Management Vlan to PortJoin Vlan to Port Statistics Statistics Rmon StatisticsStatistics Rmon History Rmon History Log TableRmon History Table Statistics Rmon Alarms Add AlarmAlarm Table Statistics Rmon Events Statistics Port UtilizationStatistics Interface Statistics Security Security 802.1x SettingsEthernet-like ParametersSecurity Port Security Setting TimerSecurity Storm Control Security Management Access ListQoS Security RadiusBroadcast Only Counts only Broadcast traffic QoS Queue Settings QoS CoS SettingsCoS Settings CoS DefaultQoS Dscp Settings QoS Basic ModeQoS Bandwidth Spanning Tree Global SettingSpanning Tree STP Status Spanning Tree Global STPSpanning Tree STP Port Settings Bridge SettingsSpeed Displays the speed at which the port is operating Multicast Vlan Igmp SettingsMulticast Igmp Snooping Multicast Bridge MulticastSnmp Global Parameters Multicast Bridge Multicast Forward AllSnmp Group Profile Snmp ViewsSnmp Group Membership Snmp CommunitiesUser Name Provides a user-defined local user list Snmp Notification Recipient Snmp Notification FilterBase Table Advanced TableAdmin User Authentication AdminUser Authentication Local User EditAdmin Static Address Admin Dynamic AddressSecure The entry is defined for locked ports Admin Cable Test Admin Port MirroringQuery Clear Table If selected, this clears the MAC Address tableAdmin Save Configuration Admin Firmware Upgrade Admin RebootAdmin Factory Default Admin Logging Admin Server LogsAdmin Memory Logs Logout Admin Flash LogsAppendix a About Gigabit Ethernet Fiber Optic Cabling Appendix aGigabit Ethernet Fiber Optic CablingAbout Switch Stacking Appendix B About Switch StackingAppendix B Stack Building Quick StartStack Resiliency Advanced StackingUnit IDs Unit ID AllocationStack Units Startup Process Master DiscoveryMaster Election User Controls Unit and Port ConfigurationStacking Examples Replacing a Failed Stack Member in a Running StackStack Master Failure and Replacement Splitting a Stack Subgroup Contains Both Master Unit and Backup Master UnitBoth Stacks Kept Running During Insertion Merging Two StacksInserting Too Many Units Stacking Cable FailureAppendix C Appendix C GlossaryGlossary Glossary Mail protocol on the Internet Packet a unit of data sent over a networkAppendix C Appendix D Specifications SpecificationsAppendix D Power in compliance with Ieee Class of Service Port-based 802.1p Vlan priority-basedDimensions Management VlanObtaining Warranty Service Warranty InformationAppendix E Exclusions and LimitationsTechnical Support Warranty InformationRegulatory Information Appendix FRegulatory Information Appendix F Norsk Norwegian Miljøinformasjon for kunder i EU Appendix F Contact Information Appendix G