Cisco Systems SLM224G4PS, SLM248G4PS manual Setup Zoom, Setup Network Settings, Identification

Page 24

Chapter 5

Configuration Using the Web-based Utility

Default Gateway  The IP address (default 0.0.0.0) of the gateway router between the Switch and management stations on other network segments. This setting can be configured from the Setup tab’s Network Settings screen.

NOTE: The Default Gateway cannot be configured if the system IP address is set to 192.168.1.254. (The system IP Address is set using Setup > Network Settings.)

Address Mode  Specifies whether the Switch’s IP address is Static or dynamically assigned using DHCP (Dynamic Host Configuration Protocol). This setting can be configured from the Setup tab’s Network Settings screen. The default setting is Static.

Base MAC Address  Displays the Switch’s MAC address.

Jumbo Frame  This setting enables or disables Jumbo frames on the Switch. A maximum packet size of 9 KB is supported. Jumbo frames allow data to be transmitted using fewer frames, providing lower overhead, quicker processing time, and fewer interruptions. Select either Enable or Disable (default).

NOTE: The Jumbo Frame feature functions only on the Gigabit ports (G1-G4).

Switch Mode After Reset  This setting specifies the system mode following a system reset. Select either Standalone or Stackable (default).

System Information

Model Name  Displays the model name of the Switch. Hardware Version  Displays the current hardware version. Boot Version  Displays the current boot version. Firmware Version  Displays the current software version

System Location  Displays the location of the system if it has been defined. This setting can be configured from the Setup tab’s Network Settings screen.

System Contact  The name of the administrator appears here, if one has been defined.This setting can be configured from the Setup tab’s Network Settings screen.

System Up Time  Displays the length of time that has elapsed since the Switch was last reset.

Current Time  Displays the current time. This setting can be configured from the Setup tab’s Time screen.

Click Save Settings to save your changes. Click Cancel Changes to cancel your changes.

Setup > Zoom

The Zoom screen depicts the status of all the ports in the system. This screen displays a front-panel view of each Switch. The color of each switch port indicates its status:

Green  This port has a connection. Gray  This port has no connection.

Orange  The administrator has closed down this port.

Setup > Zoom

Clicking on a port displays the Port Configuration screen.

NOTE: The port colors in the Zoom screen are not related to the colors of the port LEDs. The port LEDs display different status information, as described in “Chapter 2: Overview.”

Setup > Network Settings

Setup > Network Settings

The Network Settings screen allows you to edit the following information.

Identification

System Name  Specifies the name of the Switch. Enter the name into the text field provided. By default, the system name is LS-SLM224G4POEor LS-SLM248G4POE.

24/48-Port 10/100 + 4-Port Gigabit Smart Switch with Resilient Clustering Technology and PoE

18

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Port or 48-Port 10/100 + About This Guide About This GuideIcon Descriptions Online ResourcesTable of Contents Snmp Snmp Global Parameters Snmp Views Snmp Group ProfileAppendix B About Switch Stacking Gigabit Ethernet Fiber Optic CablingAppendix C Glossary Appendix D Specifications Appendix G Contact InformationChapter IntroductionSwitch LEDs and ports are located on the front panel Chapter Product OverviewProduct Overview Front PanelPower The Power port is where you connect the AC power Switch’s LEDs and ports are located on the front panelBack Panel Product Overview Chapter Installation InstallationPre-Installation Considerations Placement OptionsHardware Installation Desktop PlacementRack-Mount Placement Uplinking the Switch Configuring Stack ModeTo set up a stack with six switches, follow these steps Power off the new unit 5 the former master unit Connect port G1 on Unit 2 to port G2 on UnitConnect port G1 on Unit 3 to port G2 on Unit Chapter Configuration Using Console Interface Using telnetLogin screen appears. Proceed to the Login section below How to Use the Console Interface LoginSwitch Main Menu System Configuration MenuManagement Settings System InformationUser & Password Settings Security SettingsIP Configuration Http Restore System Default Settings Reboot SystemStack Configuration File ManagementPort Configuration Port Status MenuSystem Mode PoE SettingsHelp LogoutChapter Configuration Using Web-based Utility SetupSetup Summary Device InformationSetup Zoom Setup Network SettingsOrange The administrator has closed down this port Clicking on a port displays the Port Configuration screenSetup Time Set TimeLocal Time Daylight SavingSetup Stack Management Port Management Port SettingsPort Management Sntp ServersPort Management Port Settings Port Configuration LAG Configuration Port Management Link AggregationPort Management PoE Power Settings Port Management LacpVlan Management Port Setting Vlan ManagementVlan Management Create Vlan Vlan TableVlan Management Port to Vlan Vlan Management Vlan to PortJoin Vlan to Port Statistics Statistics Rmon StatisticsStatistics Rmon History Rmon History Log TableRmon History Table Statistics Rmon Alarms Add AlarmAlarm Table Statistics Rmon Events Statistics Port UtilizationStatistics Interface Statistics Security 802.1x Settings SecurityEthernet-like ParametersSetting Timer Security Port SecuritySecurity Management Access List Security Storm ControlQoS Security RadiusBroadcast Only Counts only Broadcast traffic QoS CoS Settings QoS Queue SettingsCoS Settings CoS DefaultQoS Dscp Settings QoS Basic ModeQoS Bandwidth Global Setting Spanning TreeSpanning Tree STP Status Spanning Tree Global STPSpanning Tree STP Port Settings Bridge SettingsSpeed Displays the speed at which the port is operating Vlan Igmp Settings MulticastMulticast Igmp Snooping Multicast Bridge MulticastMulticast Bridge Multicast Forward All Snmp Global ParametersSnmp Views Snmp Group ProfileSnmp Group Membership Snmp CommunitiesUser Name Provides a user-defined local user list Snmp Notification Filter Snmp Notification RecipientBase Table Advanced TableAdmin Admin User AuthenticationUser Authentication Local User EditAdmin Static Address Admin Dynamic AddressSecure The entry is defined for locked ports Admin Port Mirroring Admin Cable TestQuery Clear Table If selected, this clears the MAC Address tableAdmin Save Configuration Admin Firmware Upgrade Admin RebootAdmin Factory Default Admin Logging Admin Server LogsAdmin Memory Logs Admin Flash Logs LogoutAppendix a Appendix a About Gigabit Ethernet Fiber Optic CablingGigabit Ethernet Fiber Optic CablingAppendix B About Switch Stacking About Switch StackingAppendix B Stack Building Quick StartAdvanced Stacking Stack ResiliencyUnit IDs Unit ID AllocationStack Units Startup Process Master DiscoveryMaster Election Unit and Port Configuration User ControlsStacking Examples Replacing a Failed Stack Member in a Running StackStack Master Failure and Replacement Subgroup Contains Both Master Unit and Backup Master Unit Splitting a StackMerging Two Stacks Both Stacks Kept Running During InsertionStacking Cable Failure Inserting Too Many UnitsAppendix C Appendix C GlossaryGlossary Glossary Packet a unit of data sent over a network Mail protocol on the InternetAppendix C Appendix D Specifications SpecificationsAppendix D Class of Service Port-based 802.1p Vlan priority-based Power in compliance with IeeeDimensions Management VlanWarranty Information Obtaining Warranty ServiceAppendix E Exclusions and LimitationsWarranty Information Technical SupportAppendix F Regulatory InformationRegulatory Information Appendix F Norsk Norwegian Miljøinformasjon for kunder i EU Appendix F Appendix G Contact Information
Top Page Image Contents