Cisco Systems SLM224G4PS, SLM248G4PS manual QoS CoS Settings, QoS Queue Settings, CoS Default

Page 40

Chapter 5

Configuration Using the Web-based Utility

•The assignment of network traffic to a particular hardware queue

•The assignment of internal resources

•Traffic shaping

The terms Class of Service (CoS) and QoS are used in the following context:

•CoS provides varying Layer 2 traffic services. CoS refers to classifying traffic into traffic classes, where each class is handled as an aggregate whole, with no per-flow settings. CoS is usually related to the 802.1p service that classifies flows according to their Layer 2 priority, as set in the VLAN header.

•QoS refers to Layer 2 traffic and above. QoS handles per-flow settings, even within a single traffic class.

The QoS configuration options are CoS Settings, Queue Settings, DSCP Settings, and Basic Mode.

QoS > CoS Settings

The CoS Settings screen is used to enable or disable CoS.

QoS > CoS Settings

CoS Settings

QoS Mode  Indicates if QoS is enabled. The possible values are:

•Disable  Disables QoS.

•Basic  Enables QoS. This is the default value.

Class of Service  Specifies the CoS priority tag values, where 0 is the lowest and 7 is the highest.

Queue  Defines the traffic forwarding queue to which the CoS priority is mapped. Four traffic priority queues are supported.

Click Restore Defaults to restore the device factory defaults for mapping CoS values to a forwarding queue.

CoS Default

Unit No.  The unit to which the CoS configuration applies.

Default CoS  Determines the default CoS value for incoming packets for which a VLAN tag is not defined. The possible field values are 0-7. The default CoS is 0.

LAG  The LAG to which the port belongs, if relevant. If the port is a member of a LAG, the LAG settings override the port settings.

Click Save Settings to save the changes, or Cancel Changes to cancel the changes.

QoS > Queue Settings

The Queue Settings screen is used to define the QoS queue forwarding types.

QoS > Queue Settings

Strict Priority  Indicates that traffic scheduling for the selected queue is based strictly on the queue priority.

WRR  Indicates that traffic scheduling for the selected queue is based strictly on the WRR.

Queue  Displays the queue (1-4) for which the queue settings are displayed.

WRR Weight  Displays the WRR weights to queues.

%of WRR Bandwidth  Displays the percentage of bandwidth assigned to the queue. These values are fixed and cannot be modified.

Click Save Settings to save the changes, or Cancel Changes to cancel the changes.

24/48-Port 10/100 + 4-Port Gigabit Smart Switch with Resilient Clustering Technology and PoE

34

Page 39 Page 41
Image 40
Page 39 Page 41
Contents Port or 48-Port 10/100 + About This Guide About This GuideIcon Descriptions Online ResourcesTable of Contents Snmp Snmp Global Parameters Snmp Views Snmp Group ProfileAppendix B About Switch Stacking Gigabit Ethernet Fiber Optic CablingAppendix C Glossary Appendix D Specifications Appendix G Contact InformationChapter IntroductionSwitch LEDs and ports are located on the front panel Chapter Product OverviewProduct Overview Front PanelSwitch’s LEDs and ports are located on the front panel Power The Power port is where you connect the AC powerBack Panel Product Overview Chapter Installation InstallationPre-Installation Considerations Placement OptionsDesktop Placement Hardware InstallationRack-Mount Placement Configuring Stack Mode Uplinking the SwitchTo set up a stack with six switches, follow these steps Connect port G1 on Unit 2 to port G2 on Unit Power off the new unit 5 the former master unitConnect port G1 on Unit 3 to port G2 on Unit Using telnet Chapter Configuration Using Console InterfaceLogin screen appears. Proceed to the Login section below How to Use the Console Interface LoginSwitch Main Menu System Configuration MenuManagement Settings System InformationSecurity Settings User & Password SettingsIP Configuration Http Restore System Default Settings Reboot SystemStack Configuration File ManagementPort Configuration Port Status MenuSystem Mode PoE SettingsHelp LogoutChapter Configuration Using Web-based Utility SetupSetup Summary Device InformationSetup Zoom Setup Network SettingsOrange The administrator has closed down this port Clicking on a port displays the Port Configuration screenSetup Time Set TimeLocal Time Daylight SavingSetup Stack Management Port Management Port SettingsPort Management Sntp ServersPort Management Port Settings Port Configuration LAG Configuration Port Management Link AggregationPort Management PoE Power Settings Port Management LacpVlan Management Port Setting Vlan ManagementVlan Management Create Vlan Vlan TableVlan Management Vlan to Port Vlan Management Port to VlanJoin Vlan to Port Statistics Rmon Statistics StatisticsStatistics Rmon History Log Table Rmon HistoryRmon History Table Add Alarm Statistics Rmon AlarmsAlarm Table Statistics Port Utilization Statistics Rmon EventsStatistics Interface Statistics Security 802.1x Settings SecurityEthernet-like ParametersSetting Timer Security Port SecuritySecurity Management Access List Security Storm ControlSecurity Radius QoSBroadcast Only Counts only Broadcast traffic QoS CoS Settings QoS Queue SettingsCoS Settings CoS DefaultQoS Basic Mode QoS Dscp SettingsQoS Bandwidth Global Setting Spanning TreeSpanning Tree STP Status Spanning Tree Global STPBridge Settings Spanning Tree STP Port SettingsSpeed Displays the speed at which the port is operating Vlan Igmp Settings MulticastMulticast Igmp Snooping Multicast Bridge MulticastMulticast Bridge Multicast Forward All Snmp Global ParametersSnmp Views Snmp Group ProfileSnmp Communities Snmp Group MembershipUser Name Provides a user-defined local user list Snmp Notification Filter Snmp Notification RecipientBase Table Advanced TableAdmin Admin User AuthenticationUser Authentication Local User EditAdmin Dynamic Address Admin Static AddressSecure The entry is defined for locked ports Admin Port Mirroring Admin Cable TestQuery Clear Table If selected, this clears the MAC Address tableAdmin Save Configuration Admin Reboot Admin Firmware UpgradeAdmin Factory Default Admin Server Logs Admin LoggingAdmin Memory Logs Admin Flash Logs LogoutAppendix a Appendix a About Gigabit Ethernet Fiber Optic CablingGigabit Ethernet Fiber Optic CablingAppendix B About Switch Stacking About Switch StackingAppendix B Stack Building Quick StartAdvanced Stacking Stack ResiliencyUnit IDs Unit ID AllocationMaster Discovery Stack Units Startup ProcessMaster Election Unit and Port Configuration User ControlsStacking Examples Replacing a Failed Stack Member in a Running StackStack Master Failure and Replacement Subgroup Contains Both Master Unit and Backup Master Unit Splitting a StackMerging Two Stacks Both Stacks Kept Running During InsertionStacking Cable Failure Inserting Too Many UnitsAppendix C Glossary Appendix CGlossary Glossary Packet a unit of data sent over a network Mail protocol on the InternetAppendix C Specifications Appendix D SpecificationsAppendix D Class of Service Port-based 802.1p Vlan priority-based Power in compliance with IeeeDimensions Management VlanWarranty Information Obtaining Warranty ServiceAppendix E Exclusions and LimitationsWarranty Information Technical SupportAppendix F Regulatory InformationRegulatory Information Appendix F Norsk Norwegian Miljøinformasjon for kunder i EU Appendix F Appendix G Contact Information
Top Page Image Contents