Cisco Systems PA-2E3, PA-E3 manual Port adapters Port adapter lever in unlocked position

Page 39

Removing a Port Adapter

•For a Cisco uBR7223, place the port adapter lever in the unlocked position. (See Figure 6-3.)

Figure 6-3 Placing the Port Adapter Lever in the Unlocked

Position— Cisco uBR7223 Shown

Port adapters

Port adapter lever in unlocked position

16217

Step 3 Grasp the handle on the port adapter and pull the port adapter from the router midplane, about halfway out of its slot. If you are removing a blank port adapter, pull the blank port adapter completely out of the chassis slot.

Note As you disengage the port adapter from the midplane, OIR administratively shuts down all active interfaces on the port adapter.

Step 4 With the port adapter halfway out of the slot, disconnect all cables from the port adapter.

Step 5 After disconnecting the cables, pull the port adapter from its chassis slot.

Caution Always handle the port adapter by the carrier edges and handle; never touch the port adapter’s components or connector pins. (See Figure 6-4.)

Figure 6-4 Handling a Port Adapter

Metal carrier

Printed circuit board

H6420

Cisco uBR7200 Series and the PA-E3 6-3

Image 39

Contents Corporate Headquarters PA-E3 Serial Port Adapter Installation and ConfigurationPage Section Title Description PrefaceObjectives OrganizationRelated Documentation Section Title Description Related DocumentationRelated Documentation Cisco Connection Online Documentation CD-ROMCisco Connection Online Port Adapter Overview OverviewOne-Port PA-E3 Serial Port Adapter Port Adapter OverviewPA-E3 Port Adapter LEDs PA-E3 Serial Port Adapter FeaturesPA-E3 Serial Port Adapter Features Management Information BaseName Color State Description PA-E3 Receptacles and CablesPA-E3 Receptacles and Cables PA-E3 Port Adapter LEDsInteroperability Guidelines for PA-E3 DSUs 6PA-E3 Serial Port Adapter Installation and Configuration Parts and Tools Required Preparing for InstallationSoftware and Hardware Requirements Software and Hardware RequirementsPA-2E3 Safety Guidelines Safety Guidelines4PA-E3 Serial Port Adapter Installation and Configuration Electrical Equipment Guidelines Telephone Wiring GuidelinesElectrical Equipment Guidelines Preventing Electrostatic Discharge DamageTBR24 Compliance Compliance InformationBabt Compliance ITI-T ComplianceOverview VIP2 and the PA-E3Dimm U5 OverviewPA-E3 in port adapter Slot PA-E3 in port adapter slot Removing a Port Adapter Removing a Port AdapterInstalling a Port Adapter Installing a Port AdapterAligning a Port Adapter in a Port Adapter Slot H3152 8PA-E3 Serial Port Adapter Installation and Configuration Catalyst RSM/VIP2 and the PA-E3 Port adapter securing screw Removing a Port Adapter Installing a Port Adapter Aligning a Port Adapter in a Port Adapter Slot 6PA-E3 Serial Port Adapter Installation and Configuration Cisco 7206 with a PA-E3 in Port Adapter Slot Cisco 7200 Series and the PA-E3Port adapter Handle Lever unlocked Position Handling a Port Adapter Port adapter Handle Cisco uBR7200 Series and the PA-E3 Port adapters Port adapters Port adapter lever in unlocked position Inside slot guide PC board Metal carrier Port adapter retention clip in locked position 6PA-E3 Serial Port Adapter Installation and Configuration Cisco 7100 Series and the PA-E3 Installation OverviewCisco 7140 Series Router-Port Adapter Slot 4 Location Installing a Port Adapter Guides Using the Exec Command Interpreter Configuring the PA-E3 InterfacesCisco 7200 Series and Cisco uBR7200 Series Ports Cisco 7206 Serial Port Number Example Cisco 7200 Series and Cisco uBR7200 Series PortsPA-E3 Interface Port Address Example- Cisco uBR7246 Shown VIP2 PortsCatalyst RSM/VIP2 Ports Catalyst RSM/VIP2 PortsRoute Switch Module Cisco 7100 Series PortsWith port adapters Performing a Basic Conﬁguration Performing a Basic ConfigurationConfiguration Example Conﬁguration ExampleCustomizing the PA-E3 Deﬁning Set Bit National Setting the BandwidthDeﬁning the DSU Mode Setting the BandwidthSpecifying E3 Framing Setting the Cable LengthConfiguring Cyclic Redundancy Checks Conﬁguring Cyclic Redundancy ChecksUsing show Commands to Verify Status Checking the ConfigurationChecking the Conﬁguration Number Checking the Configuration StepRouter# show interfaces serial 2/0 14PA-E3 Serial Port Adapter Installation and Configuration Router# show controllers serial 0/1 Serial0/1 16PA-E3 Serial Port Adapter Installation and Configuration 73-1684-03 18PA-E3 Serial Port Adapter Installation and Configuration Using the ping Command to Verify Network Connection Using the ping Command to Verify Network ConnectionUsing the loopback Command to Verify the Physical Interface Using the loopback Command to Verify the Physical Interface 22PA-E3 Serial Port Adapter Installation and Configuration