Cisco Systems PA-E3, PA-2E3 manual Cisco 7200 Series and Cisco uBR7200 Series Ports

Page 48

Identifying Port Adapter Slot and PA-E3 Interface Port Numbers

The system prompt for the privileged level ends with a pound sign (#) instead of an angle bracket

(>). At the console terminal, use the following procedure to enter the privileged level:

Step 1 At the user-level EXEC prompt, enter the enable command. The EXEC prompts you for a privileged-level password as follows:

Router> enable

Password:

Step 2 Enter the password (the password is case-sensitive). For security purposes, the password is not displayed.

Step 3 When you enter the correct password, the system displays the privileged-level system prompt (#):

Router#

Proceed to the following section to configure the new interfaces.

Identifying Port Adapter Slot and PA-E3 Interface Port Numbers

This section describes how to identify port adapter slot and PA-E3 interface port numbers for Cisco 7200 series routers, Cisco 7100 series routers, Cisco uBR7200 series routers, and the VIP2.

You can identify interface ports by physically checking the port location on the back of the router or by using software commands to display information about a specific interface or all interfaces in the router.

The PA-E3 can be installed in the following slots on the hardware platforms described in this document:

•VIP2—Port adapter slot 0 and slot 1

•Catalyst RSM/VIP2—Port adapter slot 0 and slot 1

•Cisco 7100 series routers—Port adapter slot 3 in a Cisco 7120 series router and port adapter slot 4 in a Cisco 7140 series router

•Cisco 7200 series routers—Port adapter slot 1 and slot 2 in a Cisco 7202; port adapter slot 1 through slot 4 in a Cisco 7204 and Cisco 7204VXR; port adapter slot 1 through slot 6 in a Cisco 7206 and Cisco 7206VXR

•Cisco uBR7200 series—Port adapter slot 1 and slot 2 in a Cisco uBR7246 and port adapter slot 1 in a Cisco uBR7223

Port adapters have a handle attached, but this handle is occasionally not shown in this document to allow a full view of detail on the port adapter’s faceplate.

Cisco 7200 Series and Cisco uBR7200 Series Ports

Physical port addresses specify the actual physical location of each interface port on a Cisco 7200 series router (see Figure 8-1) or a Cisco uBR7200 series router (see Figure 8-2). This address is composed of a two-part number in the format port adapter slot number/interface port number, as follows:

•The first number identifies the chassis slot in which the PA-E3 is installed.

•The second number identifies the interface port on each PA-E3; the interface port is always numbered as interface 0 for the one-port PA-E3 and 0 or 1 for the two-port PA-2E3.

8-2PA-E3 Serial Port Adapter Installation and Configuration

Page 47 Page 49
Image 48
Page 47 Page 49
Contents PA-E3 Serial Port Adapter Installation and Configuration Corporate HeadquartersPage Preface ObjectivesOrganization Section Title DescriptionRelated Documentation Related Documentation Section Title DescriptionRelated Documentation Cisco Connection Online Documentation CD-ROMCisco Connection Online Overview Port Adapter OverviewPort Adapter Overview One-Port PA-E3 Serial Port AdapterPA-E3 Serial Port Adapter Features PA-E3 Serial Port Adapter FeaturesManagement Information Base PA-E3 Port Adapter LEDsPA-E3 Receptacles and Cables PA-E3 Receptacles and CablesPA-E3 Port Adapter LEDs Name Color State DescriptionInteroperability Guidelines for PA-E3 DSUs 6PA-E3 Serial Port Adapter Installation and Configuration Preparing for Installation Parts and Tools RequiredSoftware and Hardware Requirements Software and Hardware RequirementsPA-2E3 Safety Guidelines Safety Guidelines4PA-E3 Serial Port Adapter Installation and Configuration Telephone Wiring Guidelines Electrical Equipment GuidelinesPreventing Electrostatic Discharge Damage Electrical Equipment GuidelinesCompliance Information Babt ComplianceITI-T Compliance TBR24 ComplianceVIP2 and the PA-E3 OverviewOverview Dimm U5PA-E3 in port adapter Slot PA-E3 in port adapter slot Removing a Port Adapter Removing a Port AdapterInstalling a Port Adapter Installing a Port AdapterAligning a Port Adapter in a Port Adapter Slot H3152 8PA-E3 Serial Port Adapter Installation and Configuration Catalyst RSM/VIP2 and the PA-E3 Port adapter securing screw Removing a Port Adapter Installing a Port Adapter Aligning a Port Adapter in a Port Adapter Slot 6PA-E3 Serial Port Adapter Installation and Configuration Cisco 7200 Series and the PA-E3 Cisco 7206 with a PA-E3 in Port Adapter SlotPort adapter Handle Lever unlocked Position Handling a Port Adapter Port adapter Handle Cisco uBR7200 Series and the PA-E3 Port adapters Port adapters Port adapter lever in unlocked position Inside slot guide PC board Metal carrier Port adapter retention clip in locked position 6PA-E3 Serial Port Adapter Installation and Configuration Installation Overview Cisco 7100 Series and the PA-E3Cisco 7140 Series Router-Port Adapter Slot 4 Location Installing a Port Adapter Guides Configuring the PA-E3 Interfaces Using the Exec Command InterpreterCisco 7200 Series and Cisco uBR7200 Series Ports Cisco 7200 Series and Cisco uBR7200 Series Ports Cisco 7206 Serial Port Number ExampleVIP2 Ports PA-E3 Interface Port Address Example- Cisco uBR7246 ShownCatalyst RSM/VIP2 Ports Catalyst RSM/VIP2 PortsRoute Switch Module Cisco 7100 Series PortsWith port adapters Performing a Basic Configuration Performing a Basic ConfigurationConfiguration Example Configuration ExampleCustomizing the PA-E3 Setting the Bandwidth Defining the DSU ModeSetting the Bandwidth Defining Set Bit NationalSetting the Cable Length Configuring Cyclic Redundancy ChecksConfiguring Cyclic Redundancy Checks Specifying E3 FramingUsing show Commands to Verify Status Checking the ConfigurationChecking the Configuration Checking the Configuration Step NumberRouter# show interfaces serial 2/0 14PA-E3 Serial Port Adapter Installation and Configuration Router# show controllers serial 0/1 Serial0/1 16PA-E3 Serial Port Adapter Installation and Configuration 73-1684-03 18PA-E3 Serial Port Adapter Installation and Configuration Using the ping Command to Verify Network Connection Using the ping Command to Verify Network ConnectionUsing the loopback Command to Verify the Physical Interface Using the loopback Command to Verify the Physical Interface 22PA-E3 Serial Port Adapter Installation and Configuration
Top Page Image Contents