Cisco Systems PA-E3, PA-2E3 manual Guides

Page 46

Installing a Port Adapter

Figure 7-4 Aligning the Single-Width Port Adapter Between the Slot Guides

Guides

5
I	EN

RCVR

XMTR	RCLK FERF RL
	AIS OOF LL

FE

0

/

22132

Step 7 With the port adapter halfway in the slot, connect all required cables to the port adapter.

Step 8 After connecting all required cables, carefully slide the port adapter all the way into the slot until the port adapter is seated in the router.

Step 9 After seating the port adapter in the router, slide the locking tab up to the locked position and tighten the screws. (Figure 7-1 or Figure 7-2 shows the locking tab in the locked position.)

Note If the port adapter lever is not in the locked position, the port adapter is not completely seated in the router. Carefully pull the port adapter halfway out of the slot, reinsert it, and move the port adapter lever to the locked position.

This completes the procedure for installing a new port adapter in a Cisco 7100 series router. Proceed to Chapter 8, “Conﬁguring the PA-E3 Interfaces,” to connect the necessary cables to your port adapter.

7-4PA-E3 Serial Port Adapter Installation and Configuration

Image 46

Contents PA-E3 Serial Port Adapter Installation and Configuration Corporate HeadquartersPage Organization PrefaceObjectives Section Title DescriptionRelated Documentation Related Documentation Section Title DescriptionRelated Documentation Documentation CD-ROM Cisco Connection OnlineCisco Connection Online Overview Port Adapter OverviewPort Adapter Overview One-Port PA-E3 Serial Port AdapterManagement Information Base PA-E3 Serial Port Adapter FeaturesPA-E3 Serial Port Adapter Features PA-E3 Port Adapter LEDsPA-E3 Port Adapter LEDs PA-E3 Receptacles and CablesPA-E3 Receptacles and Cables Name Color State DescriptionInteroperability Guidelines for PA-E3 DSUs 6PA-E3 Serial Port Adapter Installation and Configuration Preparing for Installation Parts and Tools RequiredSoftware and Hardware Requirements Software and Hardware RequirementsPA-2E3 Safety Guidelines Safety Guidelines4PA-E3 Serial Port Adapter Installation and Configuration Preventing Electrostatic Discharge Damage Telephone Wiring GuidelinesElectrical Equipment Guidelines Electrical Equipment GuidelinesITI-T Compliance Compliance InformationBabt Compliance TBR24 ComplianceVIP2 and the PA-E3 OverviewOverview Dimm U5PA-E3 in port adapter Slot PA-E3 in port adapter slot Removing a Port Adapter Removing a Port AdapterInstalling a Port Adapter Installing a Port AdapterAligning a Port Adapter in a Port Adapter Slot H3152 8PA-E3 Serial Port Adapter Installation and Configuration Catalyst RSM/VIP2 and the PA-E3 Port adapter securing screw Removing a Port Adapter Installing a Port Adapter Aligning a Port Adapter in a Port Adapter Slot 6PA-E3 Serial Port Adapter Installation and Configuration Cisco 7200 Series and the PA-E3 Cisco 7206 with a PA-E3 in Port Adapter SlotPort adapter Handle Lever unlocked Position Handling a Port Adapter Port adapter Handle Cisco uBR7200 Series and the PA-E3 Port adapters Port adapters Port adapter lever in unlocked position Inside slot guide PC board Metal carrier Port adapter retention clip in locked position 6PA-E3 Serial Port Adapter Installation and Configuration Installation Overview Cisco 7100 Series and the PA-E3Cisco 7140 Series Router-Port Adapter Slot 4 Location Installing a Port Adapter Guides Configuring the PA-E3 Interfaces Using the Exec Command InterpreterCisco 7200 Series and Cisco uBR7200 Series Ports Cisco 7200 Series and Cisco uBR7200 Series Ports Cisco 7206 Serial Port Number ExampleVIP2 Ports PA-E3 Interface Port Address Example- Cisco uBR7246 ShownCatalyst RSM/VIP2 Ports Catalyst RSM/VIP2 PortsCisco 7100 Series Ports Route Switch ModuleWith port adapters Performing a Basic Configuration Performing a Basic ConﬁgurationConﬁguration Example Configuration ExampleCustomizing the PA-E3 Setting the Bandwidth Setting the BandwidthDeﬁning the DSU Mode Deﬁning Set Bit NationalConﬁguring Cyclic Redundancy Checks Setting the Cable LengthConfiguring Cyclic Redundancy Checks Specifying E3 FramingChecking the Configuration Using show Commands to Verify StatusChecking the Conﬁguration Checking the Configuration Step NumberRouter# show interfaces serial 2/0 14PA-E3 Serial Port Adapter Installation and Configuration Router# show controllers serial 0/1 Serial0/1 16PA-E3 Serial Port Adapter Installation and Configuration 73-1684-03 18PA-E3 Serial Port Adapter Installation and Configuration Using the ping Command to Verify Network Connection Using the ping Command to Verify Network ConnectionUsing the loopback Command to Verify the Physical Interface Using the loopback Command to Verify the Physical Interface 22PA-E3 Serial Port Adapter Installation and Configuration