Cisco Systems PA-2E3, PA-E3 manual Safety Guidelines

Page 15

Safety Guidelines

Note The VIP2 and Catalyst RSM/VIP2 supports online insertion and removal (OIR), but individual port adapters do not. To replace the port adapters, you must first remove the VIP2 or Catalyst RSM/VIP2 from the chassis and then replace port adapters as required. OIR is supported for port adapters in the Cisco 7100 series, Cisco 7200 series, and Cisco uBR7200 series routers. Port adapters have a handle attached, but this handle is occasionally not shown in illustrations in this publication to allow a full view of detail on the port adapter’s faceplate.

In the Cisco 7000 series, Cisco 7100 series, Cisco 7500 series, Cisco uBR7200 series routers and Catalyst 5000 family switches, there are no restrictions on slot locations or sequence; however, in the Cisco 7200 series routers, there are specific configuration guidelines that must be observed for high-bandwidth port adapters.

For specific Cisco 7200 series hardware configuration information and for memory configuration guidelines for Cisco 7200 series routers, refer to the document Cisco 7200 Series Port Adapter Hardware Configuration Guidelines , which shipped with your Cisco 7200 series chassis and is also available on the Cisco Connection Documentation, Enterprise Series CD-ROM.

To determine if your Cisco 7000 series, Cisco 7100 series, Cisco 7500 series, Cisco 7200 series, or Cisco uBR7200 series router, or the Catalyst RSM/VIP2 is compatible with the PA-E3, use the show version command to display the current hardware configuration of the router, including the system software version that is currently loaded and running.

You can check the version of the default ROM image by removing the board and checking the ROM labels, or by configuring the interface or system software to boot from ROM, restarting the system, and using the show version command to check the running version.

To display the current system software version, use the show version command. In the following example, the running system software is Release 11.1(16)CA.

Router> show version

Cisco Internetwork Operating System Software

IOS (tm) GS Software, Version 11.1(16)CA

Synced to mainline version: 11.1(10.5)

Copyright (c) 1986-1997 by cisco Systems, Inc.

Compiled Thu 22-May-97 14:32

If your system lacks the required system software and microcode, contact a customer service representative for upgrade information.

Safety Guidelines

The following are safety guidelines that you should follow when working with any equipment that connects to electrical power or telephone wiring.

Warning This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. To see translations of the warnings that appear in this publication, refer to the Regulatory Compliance and Safety Information document that accompanied this device.

Waarschuwing Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van standaard maatregelen om ongelukken te voorkomen. Voor vertalingen van de waarschuwingen die

Preparing for Installation 2-3

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Corporate Headquarters PA-E3 Serial Port Adapter Installation and ConfigurationPage Section Title Description PrefaceObjectives OrganizationRelated Documentation Section Title Description Related DocumentationRelated Documentation Cisco Connection Online Documentation CD-ROMCisco Connection Online Port Adapter Overview OverviewOne-Port PA-E3 Serial Port Adapter Port Adapter OverviewPA-E3 Port Adapter LEDs PA-E3 Serial Port Adapter FeaturesPA-E3 Serial Port Adapter Features Management Information BaseName Color State Description PA-E3 Receptacles and CablesPA-E3 Receptacles and Cables PA-E3 Port Adapter LEDsInteroperability Guidelines for PA-E3 DSUs 6PA-E3 Serial Port Adapter Installation and Configuration Parts and Tools Required Preparing for InstallationSoftware and Hardware Requirements Software and Hardware RequirementsPA-2E3 Safety Guidelines Safety Guidelines4PA-E3 Serial Port Adapter Installation and Configuration Electrical Equipment Guidelines Telephone Wiring GuidelinesElectrical Equipment Guidelines Preventing Electrostatic Discharge DamageTBR24 Compliance Compliance InformationBabt Compliance ITI-T ComplianceOverview VIP2 and the PA-E3Dimm U5 OverviewPA-E3 in port adapter Slot PA-E3 in port adapter slot Removing a Port Adapter Removing a Port AdapterInstalling a Port Adapter Installing a Port AdapterAligning a Port Adapter in a Port Adapter Slot H3152 8PA-E3 Serial Port Adapter Installation and Configuration Catalyst RSM/VIP2 and the PA-E3 Port adapter securing screw Removing a Port Adapter Installing a Port Adapter Aligning a Port Adapter in a Port Adapter Slot 6PA-E3 Serial Port Adapter Installation and Configuration Cisco 7206 with a PA-E3 in Port Adapter Slot Cisco 7200 Series and the PA-E3Port adapter Handle Lever unlocked Position Handling a Port Adapter Port adapter Handle Cisco uBR7200 Series and the PA-E3 Port adapters Port adapters Port adapter lever in unlocked position Inside slot guide PC board Metal carrier Port adapter retention clip in locked position 6PA-E3 Serial Port Adapter Installation and Configuration Cisco 7100 Series and the PA-E3 Installation OverviewCisco 7140 Series Router-Port Adapter Slot 4 Location Installing a Port Adapter Guides Using the Exec Command Interpreter Configuring the PA-E3 InterfacesCisco 7200 Series and Cisco uBR7200 Series Ports Cisco 7206 Serial Port Number Example Cisco 7200 Series and Cisco uBR7200 Series PortsPA-E3 Interface Port Address Example- Cisco uBR7246 Shown VIP2 PortsCatalyst RSM/VIP2 Ports Catalyst RSM/VIP2 PortsRoute Switch Module Cisco 7100 Series PortsWith port adapters Performing a Basic Configuration Performing a Basic ConfigurationConfiguration Example Configuration ExampleCustomizing the PA-E3 Defining Set Bit National Setting the BandwidthDefining the DSU Mode Setting the BandwidthSpecifying E3 Framing Setting the Cable LengthConfiguring Cyclic Redundancy Checks Configuring Cyclic Redundancy ChecksUsing show Commands to Verify Status Checking the ConfigurationChecking the Configuration Number Checking the Configuration StepRouter# show interfaces serial 2/0 14PA-E3 Serial Port Adapter Installation and Configuration Router# show controllers serial 0/1 Serial0/1 16PA-E3 Serial Port Adapter Installation and Configuration 73-1684-03 18PA-E3 Serial Port Adapter Installation and Configuration Using the ping Command to Verify Network Connection Using the ping Command to Verify Network ConnectionUsing the loopback Command to Verify the Physical Interface Using the loopback Command to Verify the Physical Interface 22PA-E3 Serial Port Adapter Installation and Configuration
Top Page Image Contents