Cisco Systems PA-2E3, PA-E3 manual Router# show controllers serial 0/1 Serial0/1

Page 61

Using show Commands to Display Interface and System Information

For a Catalyst RSM/VIP2, use the show controllers serial command, using arguments such as those that specify the port adapter and port numbers (port-adapter/port), to display information that is specific to the serial interface hardware. Following is an example of the show controllers serial port-adapter/interfacecommand that shows serial port 0/1 on a one-port PA-E3 installed on a Catalyst RSM/VIP2:

router# show controllers serial 0/1 Serial0/1

Mx E3(2) HW Revision 0x2, FW Revision 2.42

Framing is g751, Clock Source is Line, Bandwidth limit is 34010. National Bit is 0, International Bits are: 0 0

DSU mode 0

Data in current interval (421 seconds elapsed):

0 Line Code Violations, 0 P-bit Coding Violation 0 C-bit Coding Violation

0 P-bit Err Secs, 0 P-bit Severely Err Secs

0 Severely Err Framing Secs, 0 Unavailable Secs

0 Line Errored Secs, 0 C-bit Errored Secs, 0 C-bit Severely Errored Secs Total Data (last 1 15 minute intervals):

4 Line Code Violations, 0 P-bit Coding Violation, 0 C-bit Coding Violation,

0 P-bit Err Secs, 0 P-bit Severely Err Secs,

0 Severely Err Framing Secs, 0 Unavailable Secs,

3 Line Errored Secs, 0 C-bit Errored Secs, 0 C-bit Severely Errored Secs No alarms detected.

(Display text omitted.)

The show version (or show hardware) command displays the configuration of the system hardware (the number of each port adapter type installed), the software version, the names and sources of configuration files, and the boot images. Following is an example of the output from the

show version command on a Cisco 7200 series router:

router# show version

Cisco Internetwork Operating System Software

IOS (tm) 7200 Software (C7200-P-M), Version 11.1(16)CA

Synced to mainline version: 11.1(10.5)

Copyright (c) 1986-1997 by cisco Systems, Inc.

Compiled Thu 22-May-97 14:40

Image text-base: 0x600088F0, data-base: 0x604B6000

ROM: System Bootstrap, Version 11.1(5) [mkamson 5], RELEASE SOFTWARE (fc1)

ROM: 7200 Software (C7200-BOOT-M), Version 11.1(6), RELEASE SOFTWARE (fc1)

byron uptime is 22 minutes System restarted by reload

System image file is "paking/poet/c7200-p-mz", booted via tftp from 172.16.0.0

cisco 7206 (NPE150) processor with 12288K/4096K bytes of memory.

R4700 processor, Implementation 33, Revision 1.0 (512KB Level 2 Cache) Last reset from power-on

X.25 software, Version 2.0, NET2, BFE and GOSIP compliant.

4 Ethernet/IEEE 802.3 interfaces.

1 Serial network interface.

1 FDDI network interface.

125K bytes of non-volatile configuration memory.

1024K bytes of packet SRAM memory.

4096K bytes of Flash internal SIMM (Sector size 256K). Configuration register is 0x2

Configuring the PA-E3 Interfaces 8-15

Page 60 Page 62
Image 61
Page 60 Page 62
Contents Corporate Headquarters PA-E3 Serial Port Adapter Installation and ConfigurationPage Objectives PrefaceOrganization Section Title DescriptionRelated Documentation Section Title Description Related DocumentationRelated Documentation Documentation CD-ROM Cisco Connection OnlineCisco Connection Online Port Adapter Overview OverviewOne-Port PA-E3 Serial Port Adapter Port Adapter OverviewPA-E3 Serial Port Adapter Features PA-E3 Serial Port Adapter FeaturesManagement Information Base PA-E3 Port Adapter LEDsPA-E3 Receptacles and Cables PA-E3 Receptacles and CablesPA-E3 Port Adapter LEDs Name Color State DescriptionInteroperability Guidelines for PA-E3 DSUs 6PA-E3 Serial Port Adapter Installation and Configuration Parts and Tools Required Preparing for InstallationSoftware and Hardware Requirements Software and Hardware RequirementsPA-2E3 Safety Guidelines Safety Guidelines4PA-E3 Serial Port Adapter Installation and Configuration Electrical Equipment Guidelines Telephone Wiring GuidelinesPreventing Electrostatic Discharge Damage Electrical Equipment GuidelinesBabt Compliance Compliance InformationITI-T Compliance TBR24 ComplianceOverview VIP2 and the PA-E3Dimm U5 OverviewPA-E3 in port adapter Slot PA-E3 in port adapter slot Removing a Port Adapter Removing a Port AdapterInstalling a Port Adapter Installing a Port AdapterAligning a Port Adapter in a Port Adapter Slot H3152 8PA-E3 Serial Port Adapter Installation and Configuration Catalyst RSM/VIP2 and the PA-E3 Port adapter securing screw Removing a Port Adapter Installing a Port Adapter Aligning a Port Adapter in a Port Adapter Slot 6PA-E3 Serial Port Adapter Installation and Configuration Cisco 7206 with a PA-E3 in Port Adapter Slot Cisco 7200 Series and the PA-E3Port adapter Handle Lever unlocked Position Handling a Port Adapter Port adapter Handle Cisco uBR7200 Series and the PA-E3 Port adapters Port adapters Port adapter lever in unlocked position Inside slot guide PC board Metal carrier Port adapter retention clip in locked position 6PA-E3 Serial Port Adapter Installation and Configuration Cisco 7100 Series and the PA-E3 Installation OverviewCisco 7140 Series Router-Port Adapter Slot 4 Location Installing a Port Adapter Guides Using the Exec Command Interpreter Configuring the PA-E3 InterfacesCisco 7200 Series and Cisco uBR7200 Series Ports Cisco 7206 Serial Port Number Example Cisco 7200 Series and Cisco uBR7200 Series PortsPA-E3 Interface Port Address Example- Cisco uBR7246 Shown VIP2 PortsCatalyst RSM/VIP2 Ports Catalyst RSM/VIP2 PortsCisco 7100 Series Ports Route Switch ModuleWith port adapters Performing a Basic Configuration Performing a Basic ConfigurationConfiguration Example Configuration ExampleCustomizing the PA-E3 Defining the DSU Mode Setting the BandwidthSetting the Bandwidth Defining Set Bit NationalConfiguring Cyclic Redundancy Checks Setting the Cable LengthConfiguring Cyclic Redundancy Checks Specifying E3 FramingChecking the Configuration Using show Commands to Verify StatusChecking the Configuration Number Checking the Configuration StepRouter# show interfaces serial 2/0 14PA-E3 Serial Port Adapter Installation and Configuration Router# show controllers serial 0/1 Serial0/1 16PA-E3 Serial Port Adapter Installation and Configuration 73-1684-03 18PA-E3 Serial Port Adapter Installation and Configuration Using the ping Command to Verify Network Connection Using the ping Command to Verify Network ConnectionUsing the loopback Command to Verify the Physical Interface Using the loopback Command to Verify the Physical Interface 22PA-E3 Serial Port Adapter Installation and Configuration
Top Page Image Contents