Cisco Systems VIP-FE-TX/4E manual Versatile Interface Processor Functions

Page 14

Versatile Interface Processor Functions

The system brings on line only interfaces that match the current configuration and were previously configured as up; all others require that you configure them with the configure command. OIR functionality enables you to add, remove, or replace interface processors with the system online, which provides a method that is seamless to end users on the network, maintains all routing information, and ensures session preservation.

The function of the ejector levers (see Figure 8) is to align and seat the card connectors in the backplane. Failure to use the ejector levers and insert the interface processor properly can disrupt the order in which the pins make contact with the card or interface processor. Follow the VIP installation and removal instructions carefully, and review the following examples of incorrect insertion practices and their results:

Using the handle to force the interface processor all the way into the slot can pop the ejector levers out of their springs. If you then try to use the ejector levers to seat the interface processor, the first layer of pins (which are already mated to the card or interface processor) can disconnect and then remate with the backplane, which the system interprets as a board failure.

Using the handle to force or slam the interface processor all the way into the slot can damage the pins on the board connectors if they are not aligned properly with the backplane.

When using the handle (rather than the ejector levers) to seat the interface processor in the backplane, you might need to pull the interface processor back out and push it in again to align it properly. Even if the backplane pins are not damaged, the pins mating with and disconnecting from the card or interface processor will cause the system to interpret a board failure. Using the ejector levers ensures that the board connector mates with the backplane in one continuous movement.

Using the handle to insert or remove an interface processor, or failing to push the ejector levers fully against the interface processor, can leave some (not all) of the connector pins mated to the card or interface processor, a state which will hang the system. Using the ejector levers and making sure that they are pushed fully into position ensures that all three layers of pins are mated with (or free from) the backplane.

It is also important to use the ejector levers when removing an interface processor to ensure that the backplane connector pins disconnect from the card or interface processor in the logical sequence expected by the system. Any interface processor that is only partially connected to the backplane can hang the bus. Detailed steps for correctly performing OIR are included with the following procedures for installing and removing the VIP.

14VIP-FE-TX/4E Installation and Configuration

Image 14
Contents VIP-FE-TX/4E Installation and Configuration Table of Contents What is the VIP? Versatile Interface Processor FunctionsDram VIP Hardware Prerequisites What is the Cisco 7000 Family?VIP Software Prerequisites Cisco 7000 Series Cisco 7000, Interface Processor EndCisco 7500 Series Cisco 7010, Interface Processor EndCisco 7507, Interface Processor End Cisco 7513, Interface Processor End VIP Port Adapter Hardware Configuration Overview List of Parts and Tools VIP Installation PrerequisitesVIP Microcode Overview Safety Guidelines Electrical Equipment GuidelinesOnline Insertion and Removal-An Overview Versatile Interface Processor Functions H1984 Removing a VIP VIP InstallationRemoving an Interface Processor Filler Captive installation screws Installing a VIP Checking the Installation and Verifying VIP Status Checking the VIP InstallationVersatile Interface Processor Functions Verifying VIP Status Using show Commands Router# show controller cbus Upgrading VIP Microcode Router# show flash Loaded from Flash Upgrading and Replacing Dram SIMMs Handling a Dram SIMM-Example OnlyDram Removing and Replacing Dram SIMMs FE-TX Port Adapter Fast Ethernet OverviewVIP Port Adapter Functions Dram FE-TX Port Adapter LEDs MIIConnector FE-TX Port Adapter Receptacles, Cables, and PinoutsReceive Data + RxD+ FE-TX MII Connection, Receptacle Attaching FE-TX Port Adapter Interface Cables Configuring the FE-TX Interface Attaching the Ferrite Bead around the RJ-45 CableVIP Port Adapter Functions Fast Ethernet Interface Port Number Example Cisco 7505 Shown VIP Port Adapter Functions Configuring the FE-TX Port Adapters-Descriptions and Examples Router# configure terminal Router# show version 4E Port Adapter Ethernet 10BASE-T Overview4E Port Adapter Description and 10BASE-T Specifications Cable Specifications for 10-Mbps 10BASE-T Parameter RJ-45 4E Port Adapter LEDs 4E Port Adapter Receptacles, Cables, and PinoutsReceive Data + RxD+ Attaching 4E Port Adapter Interface Cables Configuring the 4E Interfaces VIP Port Adapter Functions 10BASE-T Interface Port Number Example Cisco 7505 Shown Router# sh int e 3/1/0 Slot Adapter Port n Slot Adapter Port Port n Router# show version Selv Circuit Warning Translations Cisco Information Online