Cisco Systems VIP-FE-TX/4E manual Dram

Page 4

Versatile Interface Processor Functions

Note The VIP port adapters themselves do not support OIR, nor are they FRUs.

The VIP uses a Reduced Instructions Set Computing (RISC), Mips 4600 processor for high performance, and has an internal operating frequency of 100 megahertz (MHz) and a 50-MHz system bus interface. The VIP has 8 megabytes (MB) of dynamic random access memory (DRAM) as the default DRAM configuration.

Figure 1 shows a VIP-FE-TX/4E. The VIP firmware (microcode), which contains card-specific software instructions, resides in a Flash memory device in socket location U17. For pinouts, refer to the section “FE-TX Port Adapter Receptacles, Cables, and Pinouts” on page 33. Single in-line memory modules contain the DRAM. You can install VIPs in any available interface processor slots in your Cisco 7000 or Cisco 7500 series router.

Figure 1 VIP with One FE-TX and One 4E Port Adapter (Product Number VIP-FE-TX/4E[=])

 

Bus connector

Microcode

Port adapter

handles not shown

Flash U17

U2

 

DRAM

U1

SIMMs

 

FE-TX in

4E in port

adapter

port adapter

slot 1

slot 0

 

FAST ETHERNET

0

MII

LINK

RJ45

0

1

2

3

1

LINK

3

0

2

ETHERNET-10BT

H4711

Note In the Cisco 7000, Cisco 7507 and Cisco 7513 chassis, the VIP is installed vertically. In the Cisco 7010 and Cisco 7505 chassis, the VIP is installed horizontally. Port adapters have a handle attached, but this handle is not shown to allow a full view of detail on each port adapter’s faceplate.

4VIP-FE-TX/4E Installation and Configuration

Image 4
Contents VIP-FE-TX/4E Installation and Configuration Table of Contents What is the VIP? Versatile Interface Processor FunctionsDram VIP Software Prerequisites What is the Cisco 7000 Family?VIP Hardware Prerequisites Cisco 7000 Series Cisco 7000, Interface Processor EndCisco 7500 Series Cisco 7010, Interface Processor EndCisco 7507, Interface Processor End Cisco 7513, Interface Processor End VIP Port Adapter Hardware Configuration Overview VIP Microcode Overview VIP Installation PrerequisitesList of Parts and Tools Safety Guidelines Electrical Equipment GuidelinesOnline Insertion and Removal-An Overview Versatile Interface Processor Functions H1984 Removing an Interface Processor Filler VIP InstallationRemoving a VIP Captive installation screws Installing a VIP Checking the Installation and Verifying VIP Status Checking the VIP InstallationVersatile Interface Processor Functions Verifying VIP Status Using show Commands Router# show controller cbus Upgrading VIP Microcode Router# show flash Loaded from Flash Upgrading and Replacing Dram SIMMs Handling a Dram SIMM-Example OnlyDram Removing and Replacing Dram SIMMs FE-TX Port Adapter Fast Ethernet OverviewVIP Port Adapter Functions Dram FE-TX Port Adapter LEDs MIIConnector FE-TX Port Adapter Receptacles, Cables, and PinoutsReceive Data + RxD+ FE-TX MII Connection, Receptacle Attaching FE-TX Port Adapter Interface Cables Configuring the FE-TX Interface Attaching the Ferrite Bead around the RJ-45 CableVIP Port Adapter Functions Fast Ethernet Interface Port Number Example Cisco 7505 Shown VIP Port Adapter Functions Configuring the FE-TX Port Adapters-Descriptions and Examples Router# configure terminal Router# show version 4E Port Adapter Ethernet 10BASE-T Overview4E Port Adapter Description and 10BASE-T Specifications Cable Specifications for 10-Mbps 10BASE-T Parameter RJ-45 4E Port Adapter LEDs 4E Port Adapter Receptacles, Cables, and PinoutsReceive Data + RxD+ Attaching 4E Port Adapter Interface Cables Configuring the 4E Interfaces VIP Port Adapter Functions 10BASE-T Interface Port Number Example Cisco 7505 Shown Router# sh int e 3/1/0 Slot Adapter Port n Slot Adapter Port Port n Router# show version Selv Circuit Warning Translations Cisco Information Online