Cisco Systems VIP-FE-TX/4E manual Configuring the 4E Interfaces

Page 50

VIP Port Adapter Functions

Step 2 Attach the ferrite bead to the RJ-45 cable (at either end), as shown in Figure 30.

Caution The ferrite bead prevents electromagnetic interference (EMI) from affecting the 4E-equipped system and is a required component for proper system operation.

Figure 30 Attaching the Ferrite Bead around the RJ-45 Cable

Ferrite bead

RJ-45 cable

 

with ferrite bead

H4202

Step 3 Attach the network end of your RJ-45 cable to your 10BASE-T hub or repeater, DTE, or other external 10BASE-T equipment.

This completes the 4E installation. Proceed to the section “Checking the VIP Installation” on page 19, then to the section “Configuring the 4E Interfaces,” which follows.

Configuring the 4E Interfaces

If you installed a new 4E port adapter or if you want to change the configuration of an existing interface, you must enter Configuration mode using the configure command. If you replaced a 4E port adapter that was previously configured, the system will recognize the new 4E interfaces and bring them up in their existing configuration.

After you verify that the new 4E port adapter is installed correctly (the enabled LED goes on), use the privileged-level configure command to configure the new interfaces. Be prepared with the information you will need, such as the following:

Protocols you plan to route on each new interface.

Internet protocol (IP) addresses if you plan to configure the interfaces for IP routing.

Whether the new interfaces will use bridging.

For a summary of the configuration options available and instructions for configuring the 4E interfaces on the VIP, refer to the Router Products Configuration Guide .

The configure command requires privileged-level access to the EXEC command interpreter, which usually requires a password. Contact your system administrator if necessary to obtain EXEC-level access. The 4E interfaces on a VIP can both be configured at 10 Mbps, half duplex (HDX) or full duplex (FDX), for a maximum aggregate bandwidth of 40 Mbps.

50VIP-FE-TX/4E Installation and Configuration

Image 50
Contents VIP-FE-TX/4E Installation and Configuration Table of Contents What is the VIP? Versatile Interface Processor FunctionsDram VIP Hardware Prerequisites What is the Cisco 7000 Family?VIP Software Prerequisites Cisco 7000 Series Cisco 7000, Interface Processor EndCisco 7500 Series Cisco 7010, Interface Processor EndCisco 7507, Interface Processor End Cisco 7513, Interface Processor End VIP Port Adapter Hardware Configuration Overview List of Parts and Tools VIP Installation PrerequisitesVIP Microcode Overview Safety Guidelines Electrical Equipment GuidelinesOnline Insertion and Removal-An Overview Versatile Interface Processor Functions H1984 Removing a VIP VIP InstallationRemoving an Interface Processor Filler Captive installation screws Installing a VIP Checking the Installation and Verifying VIP Status Checking the VIP InstallationVersatile Interface Processor Functions Verifying VIP Status Using show Commands Router# show controller cbus Upgrading VIP Microcode Router# show flash Loaded from Flash Upgrading and Replacing Dram SIMMs Handling a Dram SIMM-Example OnlyDram Removing and Replacing Dram SIMMs FE-TX Port Adapter Fast Ethernet OverviewVIP Port Adapter Functions Dram FE-TX Port Adapter LEDs MIIConnector FE-TX Port Adapter Receptacles, Cables, and PinoutsReceive Data + RxD+ FE-TX MII Connection, Receptacle Attaching FE-TX Port Adapter Interface Cables Configuring the FE-TX Interface Attaching the Ferrite Bead around the RJ-45 CableVIP Port Adapter Functions Fast Ethernet Interface Port Number Example Cisco 7505 Shown VIP Port Adapter Functions Configuring the FE-TX Port Adapters-Descriptions and Examples Router# configure terminal Router# show version 4E Port Adapter Ethernet 10BASE-T Overview4E Port Adapter Description and 10BASE-T Specifications Cable Specifications for 10-Mbps 10BASE-T Parameter RJ-45 4E Port Adapter LEDs 4E Port Adapter Receptacles, Cables, and PinoutsReceive Data + RxD+ Attaching 4E Port Adapter Interface Cables Configuring the 4E Interfaces VIP Port Adapter Functions 10BASE-T Interface Port Number Example Cisco 7505 Shown Router# sh int e 3/1/0 Slot Adapter Port n Slot Adapter Port Port n Router# show version Selv Circuit Warning Translations Cisco Information Online