Cisco Systems ACIP-SM(=) manual List of Parts and Tools, Safety Guidelines, Safety Warnings

Page 12

ACIP Installation Prerequisites

List of Parts and Tools

You need the following tools and parts to install or upgrade an ACIP. If you need additional equipment, contact your service representative for ordering information.

ACIP-SM(=) and an empty interface processor slot in your Cisco 7500 series router

Note The ACIP is not supported in Cisco 7500 series routers with an RSP4 installed. Only RSP1s and RSP2s can be used with the ACIP.

The appropriate single-mode optical-fiber cable(s) with Simplex or Duplex connections (optical-fiber cables are not available from Cisco Systems; cables are available from commercial cable vendors)

Number 2 Phillips screwdriver or a 3/16-inch flat-blade screwdriver

Appropriate multimode optical-fiber cable (not available from Cisco Systems) to connect the ACIP with the ATM network

ESD cord and wrist strap or disposable wrist strap that shipped with the ACIP

Safety Guidelines

This section lists safety guidelines to follow when working with any equipment that connects to electrical power or telephone wiring.

Safety Warnings

Safety warnings appear throughout this publication in procedures that, if performed incorrectly, might harm you. A warning symbol precedes each warning statement.

Warning Means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. To see translations of the warnings that appear in this publication, refer to the Regulatory Compliance and Safety Information document that accompanied this device.

Waarschuwing Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van standaard maatregelen om ongelukken te voorkomen. Voor vertalingen van de waarschuwingen die in deze publicatie verschijnen, kunt u het document Regulatory Compliance and Safety Information (Informatie over naleving van veiligheids- en andere voorschriften) raadplegen dat bij dit toestel is ingesloten.

Varoitus Tämä varoitusmerkki merkitsee vaaraa. Olet tilanteessa, joka voi johtaa ruumiinvammaan. Ennen kuin työskentelet minkään laitteiston parissa, ota selvää sähkökytkentöihin liittyvistä vaaroista ja tavanomaisista onnettomuuksien ehkäisykeinoista. Tässä julkaisussa esiintyvien varoitusten käännökset löydät laitteen mukana olevasta Regulatory Compliance and Safety Information -kirjasesta (määräysten noudattaminen ja tietoa turvallisuudesta).

12ATM Cable Interface Processor (ACIP) Installation and Configuration

Image 12
Contents Product Numbers ACIP-SM= ATM Terms and Acronyms Asynchronous Transfer Mode Overview Acip Features Acip DescriptionPower Budget Acip InterfaceSonet Distance Limitations Approximating the Acip Power Margin Multimode Power Budget Example of Dispersion Limit Acip Cables, PLIM, and ConnectionsDuplex SC-Type Connector Acip Installation Prerequisites Acip Software PrerequisitesHardware and Host Router Prerequisites Cisco 7507, Interface Processor End Cisco 7513, Interface Processor End Safety Guidelines Safety WarningsList of Parts and Tools Acip Installation Prerequisites Telephone Wiring Preventing Electrostatic Discharge DamageElectrical Equipment Acip Installation Prerequisites Installing and Removing an Acip Install a module as followsRemove a module as follows Using LEDs to Check Acip Status Attaching Network Interface Cables to the AcipUsing LEDs to Check Acip Status Using show Commands to Verify Interface Status Router# show versionRouter# show cont cbus Configuring the Acip Acip Defaults Parameter Command Default Value Configure an Acip InterfaceConfigure the Integrated Routing and Bridging Feature Configure Cable ParametersConfigure the Bridge-Group Virtual Interface Configure Protocols for Routing or Bridging Interface bvi bridge-groupMonitor and Maintain the Acip Configuration ExampleAcip Error Statistics ATM show CommandsChecking the Configuration Using the Debug ATM Commands Router# show atm vcExamples of ATM Error Messages Examples of ATM Error Messages F4 Segment ATMATM2/0 VC1 Bad SAP received Cisco Connection Online