Cisco Systems 7304 manual Monitoring Per-Port Interface Statistics, 13-18

Page 18

Chapter 13 Configuring the 2-Port and 4-Port T3/E3 SPAs

Verifying the Interface Configuration

Monitoring Per-Port Interface Statistics

To find detailed status and statistical information on a per-port basis for the 2-Port or 4-Port T3/E3 SPA, use the show controllers serial command. For a description of the command output, see Chapter 18, “Command Reference.”

The following example provides sample output for interface port 1 on the SPA located in the first subslot of the SIP that is installed in slot 5 of the Cisco 7304 router:

show controller serial 5/0/2 Serial5/0/2 -

Framing is c-bit, Clock Source is Line

Bandwidth limit is 44210, DSU mode 0, Cable length is 10 rx FEBE since last clear counter 0, since reset 0

Data in current interval (807 seconds elapsed):

0 Line Code Violations, 0 P-bit Coding Violation 0 C-bit Coding Violation

0 P-bit Err Secs, 0 P-bit Sev Err Secs

0 Sev Err Framing Secs, 306 Unavailable Secs

500 Line Errored Secs, 0 C-bit Errored Secs, 0 C-bit Sev Err Secs Data in Interval 1:

0 Line Code Violations, 0 P-bit Coding Violation 0 C-bit Coding Violation

0 P-bit Err Secs, 0 P-bit Sev Err Secs

0 Sev Err Framing Secs, 0 Unavailable Secs

564 Line Errored Secs, 0 C-bit Errored Secs, 0 C-bit Sev Err Secs Data in Interval 2:

0 Line Code Violations, 0 P-bit Coding Violation 0 C-bit Coding Violation

0 P-bit Err Secs, 0 P-bit Sev Err Secs

0 Sev Err Framing Secs, 0 Unavailable Secs

564 Line Errored Secs, 0 C-bit Errored Secs, 0 C-bit Sev Err Secs Data in Interval 3:

0 Line Code Violations, 0 P-bit Coding Violation 0 C-bit Coding Violation

0 P-bit Err Secs, 0 P-bit Sev Err Secs

0 Sev Err Framing Secs, 0 Unavailable Secs

562 Line Errored Secs, 0 C-bit Errored Secs, 0 C-bit Sev Err Secs Data in Interval 4:

0 Line Code Violations, 0 P-bit Coding Violation 0 C-bit Coding Violation

0 P-bit Err Secs, 0 P-bit Sev Err Secs

0 Sev Err Framing Secs, 0 Unavailable Secs

560 Line Errored Secs, 0 C-bit Errored Secs, 0 C-bit Sev Err Secs

.

.

.

Total Data (last 44 15 minute intervals):

 

 

 

 

0

Line Code Violations, 0

P-bit Coding Violation,

 

 

 

 

0

C-bit Coding Violation,

 

 

 

 

 

 

0

P-bit Err Secs, 0 P-bit Sev Err Secs,

 

 

 

 

0

Sev Err Framing Secs, 0

Unavailable Secs,

 

 

 

 

24750 Line Errored Secs, 0 C-bit Errored Secs, 0 C-bit Sev Err Secs

 

 

 

Transmitter is sending AIS.

 

 

 

 

 

Receiver has loss of signal.

 

 

 

 

 

40434 Sev Err Line Secs, 0

Far-End Err Secs, 0 Far-End Sev Err Secs

0

P-bit Unavailable Secs, 0 CP-bit Unavailable Secs

0

CP-bit Far-end Unavailable Secs

0

Near-end path failures, 0 Far-end path failures

 

 

 

Cisco 7304 Router Modular Services Card and Shared Port Adapter Software Configuration Guide

 

 

 

 

13-18

 

 

 

 

OL-4807-02

 

 

 

 

 

 

 

Image 18
Contents A P T E R 13-1Router# configure terminal Required Configuration TasksSetting the Card Type 13-2Internal line Configure the InterfaceVerifying Controller Configuration 13-3Verifying Interface Configuration 13-4Router# show controllers serial 6/0/2 brief Specifying the Interface Address on a SPA Optional ConfigurationsRouterconfig# interface serial 3/0/0 13-5Configuring Data Service Unit Mode 13-6Verifying DSU Mode 13-7Configuring Maintenance Data Link Routerconfig# interface serial slot/subslot/port13-8 Generator lic pfi port unit string Routerconfig-if#mdl string eic ficTransmit idle-signal path test-signal 13-9Configuring Scramble Verifying MDL13-10 Verifying Scramble Configuration Scrambling is enabled13-11 M13 Configuring FramingVerifying Framing Configuration G832Verifying Encapsulation Configuring EncapsulationRouterconfig-if# encapsulation hdlc ppp Frame-relay13-14 Configuring Cable LengthVerify Cable Length Setting Router# show interfaces serial 4/0/0 Serial4/0/0Verify Invert Data Setting Configuring Invert DataConfiguring the Trace Trail Buffer 13-15Snode soperator x string Verify TTB SettingsRouterconfig-if# ttb country rnode serial 13-16Saving the Configuration Verifying Per-Port Interface Status13-17 Monitoring Per-Port Interface Statistics 13-18Show controller serial 5/0/2 Serial5/0/2 DSU Configuration Example MDL Configuration Example13-19 Encapsulation Configuration Example Scrambling Configuration ExampleFraming Configuration Example Cable Length Configuration ExampleInvert Data Configuration Example Trace Trail Buffer Configuration Example13-21 13-22
Related manuals
Manual 70 pages 34.39 Kb