Cisco Systems 7304 Configure the Interface, Verifying Controller Configuration, Internal line

Page 3

Chapter 13 Configuring the 2-Port and 4-Port T3/E3 SPAs

Configuration Tasks

Configure the Interface

To set the ip address for the 2-Port or 4-Port T3/E3 SPA, complete these steps:

 

Command

Purpose

 

 

 

Step 1

Router(config)# interface serial

Selects the interface to configure and enters interface

 

slot/subslot/port

configuration mode.

 

 

slot/subslot/port— Specifies the location of the interface. See

 

 

 

the: “Specifying the Interface Address on a SPA” section on

 

 

 

page 13-5

 

 

 

Step 2

Router(config-if)# ip address

Sets the IP address and subnet mask.

 

address mask

address—IP address

 

 

 

 

mask—Subnet mask

 

 

 

Step 3

Router(config-if)# clock source

Sets the clock source to internal.

 

{internal line}

internal—Specifies that the internal clock source is used.

 

 

 

 

line—Specifies that the network clock source is used. This is

 

 

 

the default.

 

 

 

Step 4

Router(config-if)# no shut

Enables the interface.

 

 

 

Step 5

Router(config)# exit

Exits configuration mode and returns to the EXEC command

 

 

interpreter prompt.

 

 

 

 

Verifying Controller Configuration

Use the show controllers command to verify the controller configuration:

router# show controllers serial 6/0/0 Serial6/0/0 -

Framing is c-bit, Clock Source is Line

Bandwidth limit is 44210, DSU mode 0, Cable length is 10 rx FEBE since last clear counter 2, since reset 0

Data in current interval (546 seconds elapsed):

0

Line Code Violations, 0

P-bit Coding Violation

0

C-bit Coding Violation

 

 

 

 

 

0

P-bit Err Secs, 0 P-bit Sev Err Secs

0

Sev Err Framing Secs, 0 Unavailable Secs

0

Line Errored Secs, 0 C-bit Errored Secs, 0 C-bit Sev Err Secs

 

Data

in Interval 1:

 

 

 

 

 

0

Line Code Violations, 0 P-bit Coding Violation

0

C-bit Coding Violation

 

 

 

 

 

0

P-bit Err Secs, 0 P-bit Sev Err Secs

0

Sev Err Framing Secs, 0 Unavailable Secs

0

Line Errored Secs, 0 C-bit Errored Secs, 0 C-bit Sev Err Secs

.

 

 

 

 

 

 

.

 

 

 

 

 

 

.

 

 

 

 

 

 

 

Data in Interval 44:

 

 

 

 

 

0

Line Code Violations, 0 P-bit Coding Violation

0

C-bit Coding Violation

 

 

 

 

 

0

P-bit Err Secs, 0 P-bit Sev Err Secs

0

Sev Err Framing Secs, 0 Unavailable Secs

 

560 Line Errored Secs, 0 C-bit Errored Secs, 0 C-bit Sev Err Secs

 

Total Data (last 44 15 minute intervals):

0

Line Code Violations, 0 P-bit Coding Violation,

 

 

Cisco 7304 Router Modular Services Card and Shared Port Adapter Software Configuration Guide

 

 

 

 

 

 

OL-4807-02

 

 

 

13-3

 

 

 

 

 

 

Image 3
Contents 13-1 A P T E R13-2 Required Configuration TasksSetting the Card Type Router# configure terminal13-3 Configure the InterfaceVerifying Controller Configuration Internal lineVerifying Interface Configuration 13-4Router# show controllers serial 6/0/2 brief 13-5 Optional ConfigurationsRouterconfig# interface serial 3/0/0 Specifying the Interface Address on a SPA13-6 Configuring Data Service Unit Mode13-7 Verifying DSU ModeConfiguring Maintenance Data Link Routerconfig# interface serial slot/subslot/port13-8 13-9 Routerconfig-if#mdl string eic ficTransmit idle-signal path test-signal Generator lic pfi port unit stringConfiguring Scramble Verifying MDL13-10 Verifying Scramble Configuration Scrambling is enabled13-11 G832 Configuring FramingVerifying Framing Configuration M13Frame-relay Configuring EncapsulationRouterconfig-if# encapsulation hdlc ppp Verifying EncapsulationRouter# show interfaces serial 4/0/0 Serial4/0/0 Configuring Cable LengthVerify Cable Length Setting 13-1413-15 Configuring Invert DataConfiguring the Trace Trail Buffer Verify Invert Data Setting13-16 Verify TTB SettingsRouterconfig-if# ttb country rnode serial Snode soperator x stringSaving the Configuration Verifying Per-Port Interface Status13-17 Monitoring Per-Port Interface Statistics 13-18Show controller serial 5/0/2 Serial5/0/2 DSU Configuration Example MDL Configuration Example13-19 Cable Length Configuration Example Scrambling Configuration ExampleFraming Configuration Example Encapsulation Configuration ExampleInvert Data Configuration Example Trace Trail Buffer Configuration Example13-21 13-22
Related manuals
Manual 70 pages 34.39 Kb