Cisco Systems AIRCAP3602ITK9, AIRCAP3602IAK9RF specifications Pre-Installation Configuration Setup

Page 12

Pre-Installation Configuration Setup

Pre-Installation Configuration Setup

The pre-installation configuration setup is shown in Figure 4.

Figure 4 Pre-Installation Configuration Setup

Controller

Layer 3 devices

Cisco Aironet access points

272488

To perform pre-installation configuration, perform the following steps:

Step 1 Make sure that the Cisco wireless LAN controller DS port is connected to the network. Use the CLI, web-browser interface, or Cisco WCS procedures as described in the appropriate Cisco wireless LAN controller guide.

a.Make sure that access points have Layer 3 connectivity to the Cisco wireless LAN controller Management and AP-Manager Interface.

b.Configure the switch to which your access point is to attach. See the Cisco Wireless LAN Controller Configuration Guide, Release x.x for additional information.

c.Set the Cisco wireless LAN controller as the master so that new access points always join with it.

d.Make sure DHCP is enabled on the network. The access point must receive its IP address through DHCP.

12

Image 12

Contents Cisco Aironet 3600 Series Lightweight Access Points GETTING STARTED GUIDE2 Introduction to the Access Point 1 About this Guide3 Safety Instructions IMPORTANT SAFETY INSTRUCTIONStranslated safety warnings that accompanied this device. Statement SAVE THESE INSTRUCTIONS20A. Statement 5 Configurations 4 UnpackingExternal Antennas Internal Antennas Regulatory DomainsCountries Supported 6 Access Point Ports and Connectors LED indicator Figure 2 Access Point LED Indicator top-3602I Model272377 7 Configuring the Access Point The Controller Discovery ProcessPreparing the Access Point Installation Summary Performing a Pre-Installation ConfigurationPre-Installation Configuration Setup Controller Layer 3 devices Cisco Aironet access pointsStep 2 Apply power to the access point 2106 controller WS-C3550, WS-C3560, and WS-C3750 switchesC1880 switch 2600, 2610, 2611, 2621, 2650, and 2651 multiservice platformsc. If the access point shuts down, check the power source 8 Mounting the Access Point 9 Deploying the Access Point on the Wireless Network10 Installing Modules Installing a ModuleStep 5 Screw down the thumb screws on the module 11 Troubleshooting Guidelines for Using Cisco Aironet Lightweight Access PointsUsing DHCP Option Checking the Access Point LEDStatus LED LED Status Indications continued Troubleshooting the Access Point Join Process 12 Declarations of Conformity and Regulatory Information Tested To Comply With FCC Standards FOR HOME OR OFFICE USEAccess Point Models Module ModelsVCCI Statement for Japan Guidelines for Operating Cisco Aironet Access Points in Japan Japanese TranslationEnglish Translation 03-6434-6500Statement 371-Power Cable and AC Adapter Industry CanadaCanadian Compliance Statement Access Point Models European Community, Switzerland, Norway, Iceland, and LiechtensteinModule Models Page Health & Safety-EN60950-1 2005 EN 50385 The following standards were appliedEMC-EN 301.489-1 v1.8.1 EN 301.489-17 Radio-EN 300 328 v 1.7.1 EN 301.893 vDeclaration of Conformity for RF Exposure Generic Discussion on RF ExposureThis Device Meets FCC Guidelines for Exposure to Radio Waves Additional Information on RF Exposure Administrative Rules for Cisco Aironet Access Points in Taiwan Chinese TranslationAdministrative Rules for Low-power Radio-Frequency Devices Article Operation of Cisco Aironet Access Points in Brazil Regulatory InformationDeclaration of Conformity Statements Portuguese Translation13 Configuring DHCP Option 43 and DHCP Option Cisco AP c3600-ServiceProviderCisco AP c3600 14 Access Point Specifications Type + Length + ValueSpecification Categoryrefer to Channels and Maximum Power Settings for Cisco Aironet Access Point Specifications continued15 Obtaining Documentation and Submitting a Service Request

Related manuals

Manual 52 pages 58.61 Kb