Cisco Systems AIRCAP3602ITK9 Message, Type, Meaning, LED Status Indications continued

Page 20

Table 1	LED Status Indications (continued)

Message		Status	Message
Type		LED	Meaning

Operating status		Blinking blue	Software upgrade in progress

		Cycling through green,	Discovery/join process in progress
		red, and off

		Rapidly cycling	Access point location command invoked
		through blue, green,
		and red

		Blinking red	Ethernet link not operational in FlexConnect
			mode

Boot loader warnings		Blinking blue	Configuration recovery in progress (MODE
			button pushed for 2 to 3 seconds)

		Red	Ethernet failure or image recovery (MODE
			button pushed for 20 to 30 seconds)

		Blinking green	Image recovery in progress (MODE button
			released)

Boot loader errors		Red	DRAM memory test failure

		Blinking red and blue	FLASH file system failure

		Blinking red and off	Environment variable failure

			Bad MAC address

			Ethernet failure during image recovery

			Boot environment failure

			No Cisco image file

			Boot failure

Cisco IOS errors		Red	Software failure; try disconnecting and
			reconnecting unit power

		Cycling through blue,	General warning; insufficient inline power
		green, red, and off

20

Image 20

Contents

Cisco Aironet 3600 Series Lightweight Access Points GETTING STARTED GUIDE2 Introduction to the Access Point 1 About this Guide3 Safety Instructions IMPORTANT SAFETY INSTRUCTIONStranslated safety warnings that accompanied this device. Statement SAVE THESE INSTRUCTIONS20A. Statement External Antennas 5 Configurations4 Unpacking Countries Supported Internal AntennasRegulatory Domains 6 Access Point Ports and Connectors 272377 LED indicatorFigure 2 Access Point LED Indicator top-3602I Model 7 Configuring the Access Point The Controller Discovery ProcessPreparing the Access Point Installation Summary Performing a Pre-Installation ConfigurationPre-Installation Configuration Setup Controller Layer 3 devices Cisco Aironet access pointsStep 2 Apply power to the access point 2106 controller WS-C3550, WS-C3560, and WS-C3750 switchesC1880 switch 2600, 2610, 2611, 2621, 2650, and 2651 multiservice platformsc. If the access point shuts down, check the power source 8 Mounting the Access Point 9 Deploying the Access Point on the Wireless Network10 Installing Modules Installing a ModuleStep 5 Screw down the thumb screws on the module 11 Troubleshooting Guidelines for Using Cisco Aironet Lightweight Access PointsUsing DHCP Option Checking the Access Point LEDStatus LED LED Status Indications continued Troubleshooting the Access Point Join Process 12 Declarations of Conformity and Regulatory Information Tested To Comply With FCC Standards FOR HOME OR OFFICE USEAccess Point Models Module ModelsVCCI Statement for Japan Guidelines for Operating Cisco Aironet Access Points in Japan Japanese TranslationEnglish Translation 03-6434-6500Canadian Compliance Statement Statement 371-Power Cable and AC AdapterIndustry Canada Module Models Access Point ModelsEuropean Community, Switzerland, Norway, Iceland, and Liechtenstein Page Health & Safety-EN60950-1 2005 EN 50385 The following standards were appliedEMC-EN 301.489-1 v1.8.1 EN 301.489-17 Radio-EN 300 328 v 1.7.1 EN 301.893 vDeclaration of Conformity for RF Exposure Generic Discussion on RF ExposureThis Device Meets FCC Guidelines for Exposure to Radio Waves Additional Information on RF Exposure Administrative Rules for Cisco Aironet Access Points in Taiwan Chinese TranslationAdministrative Rules for Low-power Radio-Frequency Devices Article Operation of Cisco Aironet Access Points in Brazil Regulatory InformationDeclaration of Conformity Statements Portuguese TranslationCisco AP c3600 13 Configuring DHCP Option 43 and DHCP OptionCisco AP c3600-ServiceProvider 14 Access Point Specifications Type + Length + ValueSpecification Categoryrefer to Channels and Maximum Power Settings for Cisco Aironet Access Point Specifications continued15 Obtaining Documentation and Submitting a Service Request

Related manuals

Manual 40 pages 31.6 Kb

Manual 52 pages 58.61 Kb