Cisco Systems AIRCAP3602ISK9, AIRCAP3602ITK9, AIRCAP3602IAK9RF Access Point Ports and Connectors

Page 7
6Access Point Ports and Connectors

6Access Point Ports and Connectors

The 3602E model access point has external antenna connectors and the LED indictor on the top of the model, as shown in Figure 1. The 3602I model access point has integrated antennas and does not have external connectors on the top of the unit; however, it does have the LED indicator on top of the unit, as shown in Figure 2.

Figure 1 Access Point Ports and Connections (top)—3602E Model

1

2

A

B

D UAL

BAND

D UAL

BAND

 

D

U

D

D

 

AL BAN

 

C

U

D

D

 

AL BAN

43

1

Dual-band antenna connector A

3

Dual-band antenna connector C

 

 

 

 

2

Dual-band antenna connector B

4

Dual-band antenna connector D

 

 

 

 

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents
GETTING STARTED GUIDE Cisco Aironet 3600 Series Lightweight Access Points1 About this Guide 2 Introduction to the Access PointSAVE THESE INSTRUCTIONS 3 Safety InstructionsIMPORTANT SAFETY INSTRUCTIONS translated safety warnings that accompanied this device. Statement20A. Statement 4 Unpacking 5 ConfigurationsExternal Antennas Regulatory Domains Internal AntennasCountries Supported 6 Access Point Ports and Connectors Figure 2 Access Point LED Indicator top-3602I Model LED indicator272377 The Controller Discovery Process 7 Configuring the Access PointPreparing the Access Point Performing a Pre-Installation Configuration Installation SummaryController Layer 3 devices Cisco Aironet access points Pre-Installation Configuration Setup2600, 2610, 2611, 2621, 2650, and 2651 multiservice platforms Step 2 Apply power to the access point2106 controller WS-C3550, WS-C3560, and WS-C3750 switches C1880 switchc. If the access point shuts down, check the power source 9 Deploying the Access Point on the Wireless Network 8 Mounting the Access PointInstalling a Module 10 Installing ModulesStep 5 Screw down the thumb screws on the module Checking the Access Point LED 11 TroubleshootingGuidelines for Using Cisco Aironet Lightweight Access Points Using DHCP OptionStatus LED LED Status Indications continued Troubleshooting the Access Point Join Process Tested To Comply With FCC Standards FOR HOME OR OFFICE USE 12 Declarations of Conformity and Regulatory InformationModule Models Access Point ModelsVCCI Statement for Japan 03-6434-6500 Guidelines for Operating Cisco Aironet Access Points in JapanJapanese Translation English TranslationIndustry Canada Statement 371-Power Cable and AC AdapterCanadian Compliance Statement European Community, Switzerland, Norway, Iceland, and Liechtenstein Access Point ModelsModule Models Page Radio-EN 300 328 v 1.7.1 EN 301.893 v Health & Safety-EN60950-1 2005 EN 50385The following standards were applied EMC-EN 301.489-1 v1.8.1 EN 301.489-17Generic Discussion on RF Exposure Declaration of Conformity for RF ExposureThis Device Meets FCC Guidelines for Exposure to Radio Waves Additional Information on RF Exposure Chinese Translation Administrative Rules for Cisco Aironet Access Points in TaiwanAdministrative Rules for Low-power Radio-Frequency Devices Article Regulatory Information Operation of Cisco Aironet Access Points in BrazilPortuguese Translation Declaration of Conformity StatementsCisco AP c3600-ServiceProvider 13 Configuring DHCP Option 43 and DHCP OptionCisco AP c3600 Category 14 Access Point SpecificationsType + Length + Value SpecificationAccess Point Specifications continued refer to Channels and Maximum Power Settings for Cisco Aironet15 Obtaining Documentation and Submitting a Service Request
Related manuals
Manual 40 pages 31.6 Kb Manual 52 pages 58.61 Kb