Cisco Systems CISCO7301 manual Statement 22-SELV Circuit Warning

Page 12
Statement 22—SELV Circuit Warning

Translated Safety Warnings

¡Advertencia! La tarjeta FDDI modo sencillo puede emitir radiaciones láser invisibles por los orificios de los puertos cuando no se haya conectado ningún cable. Evitar la exposición y no mirar fijamente los orificios abiertos.

Varning! Osynlig laserstrålning kan avges från portöppningarna för FDDI-kortet för enkelmodsfiber när ingen kabel är ansluten (FDDI: Fiber Distributed Data Interface = gränssnitt för dataöverföring med fiberoptik). Utsätt dig inte för denna strålning och titta inte in i öppningarna.

Statement 22—SELV Circuit Warning

Warning The ports labeled “Ethernet,” “10BaseT,” “Token Ring,” “Console,” and “AUX” are safety extra-low voltage (SELV) circuits. SELV circuits should only be connected to other SELV circuits. Because the BRI circuits are treated like telephone-network voltage, avoid connecting the SELV circuit to the telephone network voltage (TNV) circuits.

Waarschuwing De poorten die "Ethernet", "10BaseT", "Token Ring", "Console" en "AUX" zijn gelabeld, zijn veiligheidscircuits met extra lage spanning (genaamd SELV = Safety Extra-Low Voltage). SELV-circuits mogen alleen met andere SELV-circuits verbonden worden. Omdat de BRI-circuits op dezelfde manier als telefoonnetwerkspanning behandeld worden, mag u het SELV-circuit niet verbinden met de telefoonnetwerkspanning (TNV) circuits.

Varoitus Portit, joissa on nimet "Ethernet", "10BaseT", "Token Ring", "Console" ja "AUX", ovat erityisen pienen jännityksen omaavia turvallisuuspiirejä (SELV-piirejä). Tällaiset SELV-piirit tulee yhdistää ainoastaan muihin SELV-piireihin. Koska perusluokan liitäntöjen (Basic Rate Interface- eli BRI-liitännät) jännite vastaa puhelinverkoston jännitettä, vältä SELV-piirin yhdistämistä puhelinverkoston jännitepiireihin (TNV-piireihin).

Attention Les ports étiquetés « Ethernet », « 10BaseT », « Token Ring », « Console » et « AUX » sont des circuits de sécurité basse tension (Safety Extra-Low Voltage ou SELV). Les circuits SELV ne doivent être interconnectés qu'avec d'autres circuits SELV. Comme les circuits BRI sont considérés comme des sources de tension de réseau téléphonique, éviter de connecter un circuit SELV à un circuit de tension de réseau téléphonique (telephone network voltage ou TNV).

Warnung Die mit "Ethernet", "10BaseT", "Token Ring", "Console" und "AUX" beschrifteten Buchsen sind Sicherheitskreise mit Sicherheitskleinspannung (Safety Extra-Low Voltage, SELV). SELV-Kreise sollten ausschließlich an andere SELV-Kreise angeschlossen werden. Da die BRI-Kreise wie Telefonnetzspannungen behandelt werden, ist der SELV-Kreis nicht an Telefonnetzspannungskreise (TNV) anzuschließen.

Avvertenza Le porte contrassegnate da "Ethernet", "10BaseT", "TokenRing", "Console" e "AUX" sono circuiti di sicurezza con tensione molto bassa (SELV). I circuiti SELV devono essere collegati solo ad altri circuiti SELV. Dato che i circuiti BRI vengono trattati come tensioni di rete telefonica, evitare di collegare il circuito SELV ai circuiti in cui è presente le tensione di rete telefonica (TNV).

Regulatory Compliance and Safety Information for the Cisco 7301 Internet Router

12

78-16178-04

 

 

Image 12
Contents Document Revision History DocumentVersions DateTranslated Safety Warnings Statement 1-Power Disconnection Warning Statement 2-Chassis Warning-Disconnecting Telephone-Network Cables Statement 4-Power Supply Warning Statement 12-Power Supply Disconnection Warning Statement 13-Circuit Breaker 15A Warning Statement 15-Chassis Warning-Rack-Mounting and Servicing Jos telineessä ei ole muita laitteita, aseta laite telineen alaosaan Advarsel Unngå fysiske skader under montering eller reparasjonsarbeid på denne enheten når den befinner seg i et kabinett. Vær nøye med at systemet er stabilt. Følgende retningslinjer er gitt for å verne om sikkerheten Statement 18-Invisible Laser Radiation Warning AVOID EXPOSURE-Invisible Laser radiation is emitted from transmit ports 1300NMStatement 22-SELV Circuit Warning Statement 33-Battery Handling Warning Statement 37-Restricted Area Warning Statement 39-Grounded Equipment Warning Statement 43-Jewelry Removal Warning Statement 52-Chassis Lifting Warning Avvertenza Il telaio va sollevato da due persone. Afferrare il telaio al di sotto del bordo inferiore e sollevare con entrambe le mani. Per evitare infortuni, mantenere la schiena diritta e sollevare il peso con le gambe, non con la schiena. Per evitare danni al telaio ed ai componenti, non provare mai a sollevare il telaio tramite le maniglie sugli alimentatori o sui processori di interfaccia oppure tramite i pannelli in plastica sulla parte anteriore del telaio. Queste maniglie non sono state progettate per sostenere il peso del telaio Statement 66-Main Disconnecting Device Statement 76-SELV Circuit Warning Statemente 77-WAN Port Static Shock Warning Statement 90-Customer Equipment Warning Statement 92-AWG Warning Statement 93-Ground Conductor Warning Statement 94-Wrist Strap Warning Statement 96-Circuit Breaker 15A Warning Statement 123-Class 1 LED Product Multimode Statement 124-More Than One Power Supply Warning Statement 140-Chassis Power ConnectionAttention Avant de connecter ou de déconnecter les câbles dalimentation pôles et terre du châssis, vérifiez que le circuit de courant continu est hors tension localisez le disjoncteur sur le panneau de commande du circuit de courant continu, poussez-le sur la position fermée OFF et, à laide dun ruban adhésif, bloquez sa poignée sur cette position Statement 142-Faceplates and Cover Panel Requirement Statement 162-EU Public Network Port Warning Statement 200-Safety Information Referral Warning Statement 1001-Work During Lightning Activity Statement 1004-Installation Instructions Statement 1008-Class 1 Laser Product Warning Statement 1027-Class 1 LED ProductStatement 1028-More Than One Power Supply Aviso Esta unidade pode ter mais de uma conexão de fonte de alimentação. Todas as conexões devem ser removidas para interromper a alimentação da unidade Statement 1030-Equipment Installation Statement 1040-Product Disposal Avvertenza Lo smaltimento di questo prodotto deve essere eseguito secondo le leggi e regolazioni locali Statement 1043-Service Personnel Warning Statement 1046-Installing or Replacing the Unit Statement 1051-Laser Radiation Avvertenza Le fibre ottiche ed i relativi connettori possono emettere radiazioni laser. I fasci di luce non devono mai essere osservati direttamente o attraverso strumenti ottici Statement 1071-Warning Definition Varoitus TÄRKEITÄ TURVALLISUUSOHJEITA Aviso INSTRUÇÕES IMPORTANTES DE SEGURANÇA Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham o dispositivo Translated Safety Warnings Statement 371-Power Cable and AC Adapter Japanese Electric Appliance and Radio LawsJapanese Electric Appliance and Radio Laws European Directives DeutschDansk EnglishRegulatory Standards Compliance SpecificationDescription Table 1 Regulatory Standards Compliance continued Telecom Analog FXOTelecom Analog FXS Telecom Analog E&MRegulatory Standards Compliance continued Telecom PRITelecom E1 Telecom T11. CSA = Canadian Standards Association 2. EN = European Norm EMC Class A Statements/Warnings FCC Class ACanada - Class A International - CISPR 22 Class AJapan - VCCI Class A Taiwan - BSMI Class ATelecom Approvals Listing GR-1089-Core Intrabuilding Lightning-Immunity RequirementsKorea - Class A FCC Part 68 NoticeService Order Code Facility Interface CodeJack Type Model NumberJapan - JATE Certification Canada - CS-03 CertificationSite Preparation and Safety Information Preparing Your Site for InstallationChoosing a Site for Installation Ensuring Overcurrent ProtectionCreating a Safe Environment Rack-Mounting the SystemEnsuring Proper Airflow Stabilizing the SystemLifting the System Power Considerations AC PowerDC Power Redundant PowerInstalling and Servicing the System Disconnecting PowerPreventing ESD Working with WAN Interfaces Working with LasersClass 1 Laser Label for a Single-Mode Fiber Port Class 1 LED Label for a Multimode Fiber PortDisposing of the System Preventing EMICovering Empty Slots Related Documentation Obtaining Documentation, Obtaining Support, and Security GuidelinesCisco 7301 Installation and Configuration Guide Cisco 7301 Quick Start Guide