Cisco Systems CISCO7301 manual Statement 162-EU Public Network Port Warning

Page 31
Statement 162—EU Public Network Port Warning

Translated Safety Warnings

¡Advertencia! Las placas frontales y los paneles de relleno cumplen tres funciones importantes: evitan la exposición a niveles peligrosos de voltaje y corriente dentro del chasis; reducen la interferencia electromagnética (EMI) que podría perturbar la operación de otros equipos y dirigen el flujo de aire de enfriamiento a través del chasis. No haga funcionar el sistema a menos que todas las tarjetas, placas frontales, cubiertas frontales y cubiertas traseras estén en su lugar.

Varning! Tomma framplattor och skyddspaneler har tre viktiga funktioner: de förhindrar att personer utsätts för farlig spänning och ström som finns inuti chassit; de innehåller elektromagnetisk interferens (EMI) som kan störa annan utrustning; och de styr riktningen på kylluftsflödet genom chassit. Använd inte systemet om inte alla kort, framplattor, fram- och bakskydd är på plats.

Statement 162—EU Public Network Port Warning

Warning If the symbol of suitability with an overlaid cross appears above a port, you must not connect the port to a public network that follows the European Union standards. Connecting the port to this type of public network can cause severe injury or damage your router.

Waarschuwing Als er een geschiktheidsymbool met een overgetrokken kruis boven een poort aanwezig is, dan mag u deze poort niet op een openbaar netwerk aansluiten dat aan de normen van de Europese Unie voldoet. Als u de poort op een dergelijk openbaar netwerk aansluit, kan dit ernstig letsel of schade aan uw router-eenheid veroorzaken.

Varoitus Jos portin päälle ilmestyy soveltuvuussymboli, jonka päällä on rasti, porttia ei saa liittää Euroopan unionin standardien mukaiseen julkiseen verkkoon. Jos portti liitetään tällaiseen julkiseen verkkoon, seurauksena voi olla henkilö- tai reititinvaurio.

Attention Pour éviter tout risque d'accident corporel et/ou de dommage matériel, si le symbole de capacité barré d'une croix apparaît au-dessus d'un port, il est vivement recommandé de ne pas connecter ce port à un réseau public aux normes de l'Union Européenne.

Warnung Wenn oberhalb des Ports das Verträglichkeitssymbol mit einem Kreuz darüber erscheint, dürfen Sie den Port nicht an ein öffentliches Netzwerk anschließen, daß den Standards der Europäischen Gemeinschaft folgt. Das Anschließen des Port an ein solches Netzwerk kann zu schweren Verletzungen führen oder Ihren Router beschädigen.

Avvertenza Se su una porta compare il simbolo di idoneità sbarrato, significa che la porta non può essere collegata a una rete pubblica a norma UE. Collegando la porta a un simile tipo di rete pubblica si possono correre seri rischi e provocare danni al proprio router.

Advarsel Hvis symbolet for anvendelse med et kryss over vises over en utgang, skal utgangen ikke kobles til et offentlig nettverk som følger EU-standardene. Hvis utgangen kobles til denne typen offentlig nettverk, kan det medføre alvorlig personskade eller skade på ruteren.

Regulatory Compliance and Safety Information for the Cisco 7301 Internet Router

 

78-16178-04

31

 

 

 

Image 31
Contents Date Document Revision HistoryDocument VersionsTranslated Safety Warnings Statement 1-Power Disconnection Warning Statement 2-Chassis Warning-Disconnecting Telephone-Network Cables Statement 4-Power Supply Warning Statement 12-Power Supply Disconnection Warning Statement 13-Circuit Breaker 15A Warning Statement 15-Chassis Warning-Rack-Mounting and Servicing Jos telineessä ei ole muita laitteita, aseta laite telineen alaosaan Advarsel Unngå fysiske skader under montering eller reparasjonsarbeid på denne enheten når den befinner seg i et kabinett. Vær nøye med at systemet er stabilt. Følgende retningslinjer er gitt for å verne om sikkerheten 1300NM Statement 18-Invisible Laser Radiation WarningAVOID EXPOSURE-Invisible Laser rad iation is emitted from transmit portsStatement 22-SELV Circuit Warning Statement 33-Battery Handling Warning Statement 37-Restricted Area Warning Statement 39-Grounded Equipment Warning Statement 43-Jewelry Removal Warning Statement 52-Chassis Lifting Warning Avvertenza Il telaio va sollevato da due persone. Afferrare il telaio al di sotto del bordo inferiore e sollevare con entrambe le mani. Per evitare infortuni, mantenere la schiena diritta e sollevare il peso con le gambe, non con la schiena. Per evitare danni al telaio ed ai componenti, non provare mai a sollevare il telaio tramite le maniglie sugli alimentatori o sui processori di interfaccia oppure tramite i pannelli in plastica sulla parte anteriore del telaio. Queste maniglie non sono state progettate per sostenere il peso del telaio Statement 66-Main Disconnecting Device Statement 76-SELV Circuit Warning Statemente 77-WAN Port Static Shock Warning Statement 90-Customer Equipment Warning Statement 92-AWG Warning Statement 93-Ground Conductor Warning Statement 94-Wrist Strap Warning Statement 96-Circuit Breaker 15A Warning Statement 123-Class 1 LED Product Multimode Statement 140-Chassis Power Connection Statement 124-More Than One Power Supply WarningAttention Avant de connecter ou de déconnecter les câbles dalimentation pôles et terre du châssis, vérifiez que le circuit de courant continu est hors tension localisez le disjoncteur sur le panneau de commande du circuit de courant continu, poussez-le sur la position fermée OFF et, à laide dun ruban adhésif, bloquez sa poignée sur cette position Statement 142-Faceplates and Cover Panel Requirement Statement 162-EU Public Network Port Warning Statement 200-Safety Information Referral Warning Statement 1001-Work During Lightning Activity Statement 1004-Installation Instructions Statement 1027-Class 1 LED Product Statement 1008-Class 1 Laser Product WarningStatement 1028-More Than One Power Supply Aviso Esta unidade pode ter mais de uma conexão de fonte de alimentação. Todas as conexões devem ser removidas para interromper a alimentação da unidade Statement 1030-Equipment Installation Statement 1040-Product Disposal Avvertenza Lo smaltimento di questo prodotto deve essere eseguito secondo le leggi e regolazioni locali Statement 1043-Service Personnel Warning Statement 1046-Installing or Replacing the Unit Statement 1051-Laser Radiation Avvertenza Le fibre ottiche ed i relativi connettori possono emettere radiazioni laser. I fasci di luce non devono mai essere osservati direttamente o attraverso strumenti ottici Statement 1071-Warning Definition Varoitus TÄRKEITÄ TURVALLISUUSOHJEITA Aviso INSTRUÇÕES IMPORTANTES DE SEGURANÇA Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham o dispositivo 78-16178-04 Japanese Electric Appliance and Radio Laws Statement 371-Power Cable and AC AdapterJapanese Electric Appliance and Radio Laws English European DirectivesDeutsch DanskSpecification Regulatory Standards ComplianceDescription Telecom Analog E&M Table 1 Regulatory Standards Compliance continuedTelecom Analog FXO Telecom Analog FXSTelecom T1 Regulatory Standards Compliance continuedTelecom PRI Telecom E11. CSA = Canadian Standards Association 2. EN = European Norm FCC Class A EMC Class A Statements/WarningsTaiwan - BSMI Class A Canada - Class AInternational - CISPR 22 Class A Japan - VCCI Class AFCC Part 68 Notice Telecom Approvals ListingGR-1089-Core Intrabuilding Lightning-Immunity Requirements Korea - Class AModel Number Service Order CodeFacility Interface Code Jack TypeCanada - CS-03 Certification Japan - JATE CertificationEnsuring Overcurrent Protection Site Preparation and Safety InformationPreparing Your Site for Installation Choosing a Site for InstallationStabilizing the System Creating a Safe EnvironmentRack-Mounting the System Ensuring Proper AirflowLifting the System Redundant Power Power ConsiderationsAC Power DC PowerDisconnecting Power Installing and Servicing the SystemPreventing ESD Class 1 LED Label for a Multimode Fiber Port Working with WAN InterfacesWorking with Lasers Class 1 Laser Label for a Single-Mode Fiber PortPreventing EMI Disposing of the SystemCovering Empty Slots Cisco 7301 Quick Start Guide Related DocumentationObtaining Documentation, Obtaining Support, and Security Guidelines Cisco 7301 Installation and Configuration Guide