Cisco Systems CISCO7301 manual Statemente 77-WAN Port Static Shock Warning

Page 21
Statemente 77—WAN Port Static Shock Warning

Translated Safety Warnings

¡Advertencia! Para evitar la sacudida eléctrica, no conectar circuitos de seguridad de voltaje muy bajo (safety extra-low voltage = SELV) con circuitos de voltaje de red telefónica (telephone network voltage = TNV). Los puertos de redes de área local (local area network = LAN) contienen circuitos SELV, y los puertos de redes de área extendida (wide area network = WAN) contienen circuitos TNV. En algunos casos, tanto los puertos LAN como los WAN usan conectores RJ-45. Proceda con precaución al conectar los cables.

Varning! För att undvika elektriska stötar, koppla inte säkerhetskretsar med extra låg spänning (SELV-kretsar) till kretsar med telefonnätspänning (TNV-kretsar). LAN-portar innehåller SELV-kretsar och WAN-portar innehåller TNV-kretsar. Vissa LAN- och WAN-portar är försedda med RJ-45-kontakter. Iaktta försiktighet vid anslutning av kablar.

Statemente 77—WAN Port Static Shock Warning

Warning Hazardous network voltages are present in WAN ports regardless of whether power to the unit is OFF or ON. To avoid electric shock, use caution when working near WAN ports. When detaching cables, detach the end away from the unit first.

Waarschuwing Er is gevaarlijke netwerkspanning aanwezig in WAN poorten ongeacht of de stroom naar de router INGESCHAKELD of UITGESCHAKELD is. Om elektrische schokken te vermijden, dient u voorzichtig te werk te gaan wanneer u in de nabijheid van WAN poorten werkt. Wanneer u kabels losmaakt, dient u eerst het uiteinde dat zich het verst van de eenheid vandaan bevindt, te verwijderen.

Varoitus WAN-porteissa on vaarallisia verkkojännitteitä riippumatta siitä, onko yksikön virta kytketty vai ei. Välttyäksesi sähköiskulta ole varovainen työskennellessäsi WAN-porttien lähettyvillä. Kun irrotat kaapeleita, irrota yksiköstä kauimpana sijaitseva pää ensiksi.

Attention Les ports de réseau longue distance (WAN) gèrent des tensions de réseau dangereuses, que l'unité soit sous tension ou pas. Pour éviter tout risque d’électrocution, prenez toutes les précautions nécessaires avant de travailler à proximité des ports WAN. Pour déconnecter les câbles, commencez par débrancher l’extrémité la plus éloignée du routeur.

Warnung In WAN-Ports sind gefährliche Netzspannungen vorhanden, auch wenn der Strom zur Einheit abgeschaltet wurde. Zur Vermeidung von Elektroschock Vorsicht bei der Arbeit in der Nähe von WAN-Ports. Beim Abtrennen von Kabeln zuerst das vom Router entfernte Ende lösen.

Avvertenza Nelle porte WAN sono presenti tensioni di rete pericolose, sia che il sistema sia acceso o meno (ON od OFF). Per evitare scosse elettriche, fare attenzione quando si lavora in prossimità di porte WAN. Quando si scollegano cavi, staccare per primo il connettore collegato al router.

Advarsel! Det er livsfarlig nettverksspenning i WAN-utganger, uavhengig av om strømmen til enheten er slått av (OFF) eller på (ON). Vær forsiktig når du jobber nær WAN-utganger slik at du unngår elektrisk støt. Hvis du skal løsne kabler, må du først løsne den enden som er lengst borte fra fordelingsenheten.

Regulatory Compliance and Safety Information for the Cisco 7301 Internet Router

 

78-16178-04

21

 

 

 

Image 21
Contents Document Document Revision HistoryVersions DateTranslated Safety Warnings Statement 1-Power Disconnection Warning Statement 2-Chassis Warning-Disconnecting Telephone-Network Cables Statement 4-Power Supply Warning Statement 12-Power Supply Disconnection Warning Statement 13-Circuit Breaker 15A Warning Statement 15-Chassis Warning-Rack-Mounting and Servicing Jos telineessä ei ole muita laitteita, aseta laite telineen alaosaan Advarsel Unngå fysiske skader under montering eller reparasjonsarbeid på denne enheten når den befinner seg i et kabinett. Vær nøye med at systemet er stabilt. Følgende retningslinjer er gitt for å verne om sikkerheten AVOID EXPOSURE-Invisible Laser rad Statement 18-Invisible Laser Radiation Warningiation is emitted from transmit ports 1300NMStatement 22-SELV Circuit Warning Statement 33-Battery Handling Warning Statement 37-Restricted Area Warning Statement 39-Grounded Equipment Warning Statement 43-Jewelry Removal Warning Statement 52-Chassis Lifting Warning Avvertenza Il telaio va sollevato da due persone. Afferrare il telaio al di sotto del bordo inferiore e sollevare con entrambe le mani. Per evitare infortuni, mantenere la schiena diritta e sollevare il peso con le gambe, non con la schiena. Per evitare danni al telaio ed ai componenti, non provare mai a sollevare il telaio tramite le maniglie sugli alimentatori o sui processori di interfaccia oppure tramite i pannelli in plastica sulla parte anteriore del telaio. Queste maniglie non sono state progettate per sostenere il peso del telaio Statement 66-Main Disconnecting Device Statement 76-SELV Circuit Warning Statemente 77-WAN Port Static Shock Warning Statement 90-Customer Equipment Warning Statement 92-AWG Warning Statement 93-Ground Conductor Warning Statement 94-Wrist Strap Warning Statement 96-Circuit Breaker 15A Warning Statement 123-Class 1 LED Product Multimode Statement 140-Chassis Power Connection Statement 124-More Than One Power Supply WarningAttention Avant de connecter ou de déconnecter les câbles dalimentation pôles et terre du châssis, vérifiez que le circuit de courant continu est hors tension localisez le disjoncteur sur le panneau de commande du circuit de courant continu, poussez-le sur la position fermée OFF et, à laide dun ruban adhésif, bloquez sa poignée sur cette position Statement 142-Faceplates and Cover Panel Requirement Statement 162-EU Public Network Port Warning Statement 200-Safety Information Referral Warning Statement 1001-Work During Lightning Activity Statement 1004-Installation Instructions Statement 1027-Class 1 LED Product Statement 1008-Class 1 Laser Product WarningStatement 1028-More Than One Power Supply Aviso Esta unidade pode ter mais de uma conexão de fonte de alimentação. Todas as conexões devem ser removidas para interromper a alimentação da unidade Statement 1030-Equipment Installation Statement 1040-Product Disposal Avvertenza Lo smaltimento di questo prodotto deve essere eseguito secondo le leggi e regolazioni locali Statement 1043-Service Personnel Warning Statement 1046-Installing or Replacing the Unit Statement 1051-Laser Radiation Avvertenza Le fibre ottiche ed i relativi connettori possono emettere radiazioni laser. I fasci di luce non devono mai essere osservati direttamente o attraverso strumenti ottici Statement 1071-Warning Definition Varoitus TÄRKEITÄ TURVALLISUUSOHJEITA Aviso INSTRUÇÕES IMPORTANTES DE SEGURANÇA Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham o dispositivo 78-16178-04 Statement 371-Power Cable and AC Adapter Japanese Electric Appliance and Radio LawsJapanese Electric Appliance and Radio Laws Deutsch European DirectivesDansk EnglishRegulatory Standards Compliance SpecificationDescription Telecom Analog FXO Table 1 Regulatory Standards Compliance continuedTelecom Analog FXS Telecom Analog E&MTelecom PRI Regulatory Standards Compliance continuedTelecom E1 Telecom T11. CSA = Canadian Standards Association 2. EN = European Norm FCC Class A EMC Class A Statements/WarningsInternational - CISPR 22 Class A Canada - Class AJapan - VCCI Class A Taiwan - BSMI Class AGR-1089-Core Intrabuilding Lightning-Immunity Requirements Telecom Approvals ListingKorea - Class A FCC Part 68 NoticeFacility Interface Code Service Order CodeJack Type Model NumberCanada - CS-03 Certification Japan - JATE CertificationPreparing Your Site for Installation Site Preparation and Safety InformationChoosing a Site for Installation Ensuring Overcurrent ProtectionRack-Mounting the System Creating a Safe EnvironmentEnsuring Proper Airflow Stabilizing the SystemLifting the System AC Power Power ConsiderationsDC Power Redundant PowerInstalling and Servicing the System Disconnecting PowerPreventing ESD Working with Lasers Working with WAN InterfacesClass 1 Laser Label for a Single-Mode Fiber Port Class 1 LED Label for a Multimode Fiber PortDisposing of the System Preventing EMICovering Empty Slots Obtaining Documentation, Obtaining Support, and Security Guidelines Related DocumentationCisco 7301 Installation and Configuration Guide Cisco 7301 Quick Start Guide