Baracoda
manual
RoadRunners Evolution -L 1D & -LA Laser Programming Guide
Bluetooth
General default settings
Switch on delay
AIM Symbology Identifier
Buzzer and Led Settings
Enable/Disable Codabar
Reading Mode
Page 1
Data Capture for Workforce in Motion
RoadRunners Evolution
–L
(1D) &
-LA
(Laser)
Programming Guide
©Baracoda
TM
– July 2009
Page 1
Page 2
Image 1
Page 1
Page 2
Contents
RoadRunners Evolution -L 1D & -LA Laser Programming Guide
Summary
Appendix 1 Ascii Table A-Z, A-Z, 0-9, PUNCTUATION, Control
Revision History
Introduction
General default settings
General Configuration
Switch on delay
Baracoda advanced features
Shutdown timers
Turn scanner OFF
No data loss mode and Baracoda Header
Reading Mode
Autoscan
Real Time mode
Operating Mode
No Data Loss mode Enable ACK beep
Real Time mode
No Data Loss mode Disable ACK beep
Real Time Buffered data option
Batch Mode
Batch mode
Different connection methods
LED OFF
Buzzer and Led Settings
Bluetooth name
Bluetooth settings
Sniff period settings
RF Power emission settings
Security code PIN settings
Timestamp option
Data format
YES
Data Prefix/Suffix
Barcode Prefix/Suffix
AIM Symbology Identifier
Enable/Disable All Symbologies
Decoder default settings
Set decoder barcode length
Voting
Min/Max length per symbology
Symbology table
Codabar settings
Enable/Disable Codabar
Codabar Check Digit Verification AIM recommendation
Codabar Start/Stop characters
Set Lengths for Codabar
Enable/Disable Code
Code 11 Settings
Code 11 check digits verification
Transmit Code 11 check digits
Enable/Disable Code 39 Full Ascii
Code 39 settings
Code 39 Start/stop characters
Code 39 Check Digit Verification
Accepted Code 39 characters
Set lengths for Code
Italian PharmaCode settings
Code 93 Settings
Enable/Disable Code 128/EAN
Code 128 Settings
Set lengths for Code 128/EAN
EAN 128 Group Separator
Enable/Disable AIM ID Transmission
Interleaved 2 of 5 Settings
Enable/Disable Interleaved 2
Interleaved 2of 5 Check Digit
Enable/Disable MSI
MSI Code Settings
Set lengths for Interleaved 2
MSI Check Digit
Enable/Disable Standard 2
Standard 2 of 5 Settings
Set lengths for MSI
Standard 2 of 5 Check Digit
Enable/Disable UPC/EAN
UPC/ EAN Settings
Set lengths for Standard 2
Transmit UPC-E Check Digit
Transmit EAN13 Check Digit
Transmit EAN 8 Check Digit
Transmit UPC-A Check Digit
UPC-A, UPC-E, EAN conversions
Transmit UPC number system for UPC-E
Add-on digits settings
ISSN/ISBN settings
Enable/Disable GS1 DataBar
15. GS1 DataBar RSS 14 Settings
15.2. GS1 DataBar 14 Check Digit Transmission
15.3. GS1 DataBar 14 Linkage flag Transmission
Enable/Disable GS1 DataBar Limited
16. GS1 DataBar RSS Limited Settings
16.2. GS1 DataBar Limited Check Digit Transmission
16.3. GS1 DataBar Limited Linkage flag Transmission
Capital letters A-Z
Small letters a-z
Ponctuation
Decimal numbers
Control Characters
Appendix 2 AIM symbology identifiers structure
Related pages
Troubleshooting for Motorola H700
Specifications for Dell 7609WU
Service Error Message Table for Lexmark 4040-FIN
17. Power Mesh, Schematic Diagram, Models 6680A, 6681A Only for Agilent Technologies 6682A
Microphone Announcements When Operated by Control Input for TOA Electronics VM-2120
Thermostat Installation for Empire Products FAW-40-1IP
Parts List for Kenmore 19501
Code List for RCA RC5920P
Close the shield, and then the access door for Lexmark 35S5701
Where can I find
instructions for the universal cassette clamp Leica
?
Top
Page
Image
Contents