Baracoda LA manual Interleaved 2 of 5 Settings, Enable/Disable AIM ID Transmission

Page 34

Data Capture for Workforce in Motion

2.10.4.Enable/Disable AIM ID Transmission

Even if the “AIM ID transmit” is disabled, it is possible to enable the AIM ID transmission for EAN128.

Enable AIM ID transmission for EAN128

Disable AIM ID transmission for EAN128 (*)

2.11.Interleaved 2 of 5 Settings

2.11.1.Enable/Disable Interleaved 2 of 5

To enable or disable Interleaved 2 of 5, scan the appropriate barcode below

Interleaved 2 of 5 - not active

Interleaved 2 of 5 – active (*)

2.11.2.Interleaved 2of 5 Check Digit

Interleaved 2 of 5 - check digit - not used (*)

Interleaved 2 of 5 - check digit - mod 10 - checked and

transmitted

Interleaved 2 of 5 - check digit - mod 10 - checked but not

transmitted

RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.3

- 34 -

Image 34

Contents RoadRunners Evolution -L 1D & -LA Laser Programming Guide Summary Appendix 1 Ascii Table A-Z, A-Z, 0-9, PUNCTUATION, Control Revision History Introduction General Configuration General default settingsShutdown timers Baracoda advanced featuresSwitch on delay Turn scanner OFFReading Mode No data loss mode and Baracoda HeaderAutoscan Operating Mode Real Time modeNo Data Loss mode Disable ACK beep Real Time modeNo Data Loss mode Enable ACK beep Real Time Buffered data optionBatch mode Batch ModeDifferent connection methods Buzzer and Led Settings LED OFFBluetooth settings Bluetooth nameSniff period settings Security code PIN settings RF Power emission settingsData format Timestamp optionYES Data Prefix/Suffix Barcode Prefix/Suffix AIM Symbology Identifier Enable/Disable All Symbologies Decoder default settingsSet decoder barcode length Voting Min/Max length per symbology Symbology table Codabar settingsEnable/Disable Codabar Codabar Check Digit Verification AIM recommendation Codabar Start/Stop charactersSet Lengths for Codabar Code 11 check digits verification Code 11 SettingsEnable/Disable Code Transmit Code 11 check digitsEnable/Disable Code 39 Full Ascii Code 39 settingsCode 39 Start/stop characters Code 39 Check Digit Verification Accepted Code 39 charactersSet lengths for Code Code 93 Settings Italian PharmaCode settingsEnable/Disable Code 128/EAN Code 128 SettingsSet lengths for Code 128/EAN EAN 128 Group Separator Enable/Disable Interleaved 2 Interleaved 2 of 5 SettingsEnable/Disable AIM ID Transmission Interleaved 2of 5 Check DigitSet lengths for Interleaved 2 MSI Code SettingsEnable/Disable MSI MSI Check DigitSet lengths for MSI Standard 2 of 5 SettingsEnable/Disable Standard 2 Standard 2 of 5 Check DigitEnable/Disable UPC/EAN UPC/ EAN SettingsSet lengths for Standard 2 Transmit EAN 8 Check Digit Transmit EAN13 Check DigitTransmit UPC-E Check Digit Transmit UPC-A Check DigitTransmit UPC number system for UPC-E UPC-A, UPC-E, EAN conversionsISSN/ISBN settings Add-on digits settings15.2. GS1 DataBar 14 Check Digit Transmission 15. GS1 DataBar RSS 14 SettingsEnable/Disable GS1 DataBar 15.3. GS1 DataBar 14 Linkage flag Transmission16.2. GS1 DataBar Limited Check Digit Transmission 16. GS1 DataBar RSS Limited SettingsEnable/Disable GS1 DataBar Limited 16.3. GS1 DataBar Limited Linkage flag TransmissionCapital letters A-Z Small letters a-z Ponctuation Decimal numbers Control Characters Appendix 2 AIM symbology identifiers structure