Cisco Systems SPA3102 manual LAN Network Settings, Static Dhcp Lease Settings

Page 36

Voice Gateway with Router

The Router - LAN Setup Screen

This screen lets you configure the local network, dynamic DHCP, and static DHCP lease settings.

Networking Service. Select the service you want to use, NAT or Bridge. The default is NAT.

LAN Network Settings

LAN IP Address. Enter the local IP address of the Voice Gateway. The default is 192.168.0.1.
LAN Subnet Mask. Select the local subnet mask: 255.255.255.0, 255.255.255.128, 255.255.255.192,
255.255.255.224, 255.255.255.240, 255.255.255.248, or 255.255.255.252. The default is	Figure 6-6: Router - LAN Setup Screen
255.255.255.0.	Figure 6-6: Router - LAN Setup Screen
Enable DHCP Server. To use the Voice Gateway as a router assigning IP addresses, select yes. Otherwise, select
no. The default is yes.
DHCP Lease Time. Enter the lease time used by the Voice Gateway to distribute IP addresses. The default is 24
Hours.
DHCP Client Starting IP Address. When the Voice Gateway issues IP addresses, it starts with the first value of
its DHCP client IP address range. Enter that value here. The default is 192.168.0.2.
Number of Client IP Addresses. Enter the number of IP addresses that can be distributed. The default is 50.

Static DHCP Lease Settings

Enable. You can have the Voice Gateway assign the same IP address to a specific device. To disable this feature, select no. To use this feature, select yes. The default is no.

28	Chapter 6: Using the Web-based Utility
	The Router Tab

Image 36

Contents Voice Gateway with Router Page How to Use this Guide Copyright and TrademarksVoice Gateway with Router Table of Contents Common Problems and Solutions Frequently Asked Questions Internet Telephony Service Provider Itsp LinksysBack Panel Front Panel12 Voice User 1 Screen Introduction WelcomeWhat’s in this Guide? Introduction What’s in this Guide? Voice Gateway with Router Networking Basics An Introduction to Local Area NetworksUse of IP Addresses Networking Basics Getting to Know the Voice Gateway Back PanelFront Panel Power Front PanelConnecting the Voice Gateway Getting StartedBefore You Begin Connect a PC Configuring the Voice Gateway DhcpStatic IP Settings Using the Interactive Voice Response Menu Accessing the Interactive Voice Response MenuOverview Using the Interactive Voice Response Menu Interactive Voice Response Menu Firmware the programming code that runs a networking device Set Network or 121 Enter the network or Set the Mode 201 Press 0 to select Entering a Password Enter 1 to confirm. You will hear, OptionConfiguring the Settings for Your Internet Phone Service Using the Web-based Utility RouterHow to Access the Web-based Utility VoiceRouter Tab Product InformationSystem Status Packet a unit of data sent over a network Internet Connection Settings Static IP SettingsPPPoE Settings Optional Settings MAC Clone SettingsQOS Settings Remote ManagementVlan Virtual Local Area Network Settings LAN Network Settings Static Dhcp Lease SettingsVoice Gateway with Router Port Forwarding Settings DMZ SettingsMiscellaneous Settings System Reserved Ports RangeVoice Tab Voice Info ScreenLine 1 Status Line 1 StatusVoice Gateway with Router Pstn Line Status 10 Pstn Line StatusVoice Gateway with Router Voice Gateway with Router Voice Gateway with Router System Configuration Voice System ScreenCall Forward Settings Selective Call Forward SettingsVoice User 1 Screen Voice Gateway with Router Speed Dial Settings Supplementary Service SettingsDistinctive Ring Settings Ring SettingsVoice Gateway with Router PSTN-To-VoIP Selective Call Forward Settings Voice Pstn User ScreenPSTN-To-VoIP Speed Dial Settings 16 PSTN-To-VoIP Speed Dial SettingsPstn Ring Thru Line 1 Distinctive Ring Settings 17 Pstn Ring Thru Line Distinctive Ring SettingsPstn Ring Thru Line 1 Ring Settings 18 Pstn Ring Thru Line 1 Ring SettingsAppendix a Troubleshooting Common Problems and SolutionsFor Windows 98 and Millennium Need to set a static IP address on a PCFor Windows For Windows XPWant to test my Internet connection For Windows XP Voice Gateway with Router Need to set up a server behind my Voice Gateway TCP UDP Can’t get the Internet game, server, or application to work For Microsoft Internet Explorer 5.0 or higher For Netscape 4.7 or higherFrequently Asked Questions Can I make calls if my Internet connection is down?Does the Voice Gateway support ICQ send file? How can I block corrupted FTP downloads? Which modems are compatible with the Voice Gateway? Voice Gateway with Router Figure B-1 IP Configuration Screen Windows 98 or Me InstructionsWindows 2000 or XP Instructions For the Voice Gateway’s Web-based UtilityAppendix C Windows Help Shared ResourcesNetwork Neighborhood/My Network Places Appendix C Windows Help Appendix D Glossary Appendix D Glossary Voice Gateway with Router Voice Gateway with Router Appendix E Specifications Voice Gateway Re-registration with Primary SIP Proxy ServerCodec Name Assignment Hook Flash Event Signaling AdministrationMaintenance Automated Provisioning & Upgrade via HTTP, Tftp Non-intrusive, In-Service UpgradesRing Voltage 40-55 Vrms Configurable RJ-11 FXO Phone Ports For a Telco or PBX ConnectionNorth America 600 ohms, European CTR21 10 to 90% Non-condensing, operating and non-operating Voice Gateway with Router Appendix F Warranty Information Appendix F Warranty Information Appendix G Regulatory Information FCC StatementAppendix G Regulatory Information Voice Gateway with Router Voice Gateway with Router Voice Gateway with Router Voice Gateway with Router Voice Gateway with Router Voice Gateway with Router Internet Telephony Service Provider Itsp Appendix H Contact InformationLinksys For support, contact your ItspAppendix H Contact Information

Related manuals

Manual 250 pages 30.56 Kb