Cabletron Systems STHI manual Related Manuals, Getting Help, Local Management

Page 17

Related Manuals

1.2.9Local Management

The STHI hub’s Local Management application displays packet and error statistics for the entire stack, for each individual device, or for individual ports, and enables the user to provide management support for the STHI and all its attached segments.

Users with actual or emulated VT100 dumb terminals may access Local Management out-of-band via the RJ45 COM port. Refer to Section 5.1 for connection instructions.

1.2.10 Remote Network Management Capabilities

The STHI may be managed remotely by a variety of SNMP network management systems including the following from Cabletron Systems:

•Cabletron Systems SPECTRUM

•Cabletron Systems Remote LANVIEW/Windows

•Cabletron Systems Remote LANVIEW for SunNet Manager

1.3 Related Manuals

Use the Cabletron Systems STH-22/24 /42/44 User’s Guide to supplement the procedures and other technical data provided in this manual. The procedures contained therein are referenced where appropriate, but are not repeated in this manual.

1.4 Getting Help

To present any questions, comments, or suggestions concerning this manual or any Cabletron Systems Product, please contact Cabletron Systems Technical Support:

By phone	(603) 332-9400
	Monday-Friday; 8am - 8pm EST
By CompuServe	GO CTRON from any ! prompt
By Internet mail	support@ctron.com
By Fax:	(603) 337-3075
By BBS:	(603) 337-3750

Page 1-8

Image 17

Contents Sthi Intelligent Token Ring Stackable HUB USER’S Guide Page FCC Notice Cabletron Software Program License United States Government Restricted Rights Introduction Requirements & SpecificationsInstallation Local Management TroubleshootingAppendix a Tpim Specifications Appendix B Media Specifications Sthi Overview Contents of This ManualLanview LEDs Sthi OverviewTCU Ports Lobe Port and Multiple Ring Out Port ConfigurationsRing Speed Fault Protection Media Type Connector Daughter Board Upgrade KitActive Circuitry 3 RI & RO PortsSupport for Passive MAU Workgroups Automatic Beacon Recovery ProcessHub-By-Hub Bypass Control IP Address Discovery Improved Protection from BeaconingFlash Downloads DAISY-CHAIN MAU Configuration Getting Help Related ManualsRelated Manuals Local ManagementGetting Help Maximum Number of Stations on a Ring General Networking ConsiderationsInstallation Recommendations TemperatureGeneral Networking Considerations CrosstalkOperating Specifications Operating SpecificationsHubstack Interconnect Cables TCU and COM PortsRJ45 to DB25 Connector Pinout Standard MIBs Supported MIB GroupsCabletron Enterprise MIBs Ring SpeedRing Sequence SafetyEnvironmental Requirements Physical SpecificationsComputing Hardware Unpacking the Sthi Installing the SthiStacking the Sthi Installing the SthiAttaching the Strain Relief Bracket Rack-Mounting the SthiRack Mounting Brackets Wall-Mounting the SthiInstalling the Sthi Wall-mounting the Sthi Free-Standing InstallationsFinishing the Installation Tpim InstallationTpim Installation Connecting the Sthi to the Power SourceColor Condition Lanview LED SignalsTrouble Resolution Trouble ResolutionLoss Of Power Failure to Link on Enabled PortReset Button Reset ButtonReset Button Management FailureNvram Reset Switch Nvram Reset SwitchLocal Management Accessing LMMenu Parameter Setting Accessing LMDumb Terminal Configuration Entering LM Console Cable ConfigurationUsing LM Screens Using LM ScreensInvoking Menu Options or Screen Commands Working with LM ScreensExiting the Local Management Interface Session Setting or Modifying FieldsScreen Hierarchy Password Screen Main Menu Device Setup StatusScreen Introductions System LevelChassis Status View Snmp TrapsComponent Status Device StatisticsSystem Level Screen System Level ScreenSystem Date and System Time IP AddressRetry Interval Enable IP Address DiscoverySubnet Mask Number of Retries Enable Beacon RecoverySnmp Community Names Screen Locally Administered AddressSnmp Community Names Screen MAC AddressCommunity Name Access PolicyRead-only Read-writeSnmp Traps Screen Enable TrapsSnmp Traps Screen Trap DestinationChassis Status View Screen Screen Mode Screen CommandChassis Status View Screen Functions of the Chassis Status View ScreenMultiplexer Configuration Fields Administrative Mode Port Configuration FieldsEach port field whether Tpim or TCU may be set as follows Ring OUT Enable Mode Each Ring port Tpim port or Ring Out TCU may be listed as Operational ModeNext and Previous Component Status ScreenComponent Status Screen Device Statistics Screen Device Statistics ScreenAccumulate Screen ModeFrames Received Errors ReceivedKBytes Received Beacon StatesRing Status Ports EnabledRing Number Stations on a RingLine Errors Isolating Errors Fields GroupBurst Errors AC ErrorsNon-Isolating Errors Group Internal ErrorsLost Frame Errors Frame Copied ErrorsFrequency Errors Token ErrorsSnmp Tool Screen Snmp Tool Screen3 GET OID PrependStep Getnext9 SET WalkCycles Firmware Image Downloads RepeatCtDLCommitRAMtoFlash Twisted Pair Tpim Pinouts OverviewFiber Optic Tpim Specifications Fiber Optic Tpim SpecificationsBudget TPIM-F2 for Multimode FiberParameter Typical Worst Case Parameter Typical Minimum Maximum TPIM-F3 for Single Mode FiberA-5 UTP Cable Categories Unshielded Twisted Pair UTPUnshielded Twisted Pair UTP Operating Electrical SignalAttenuation Loss Cat Frequency Per 100m @ ≥100mShielded Twisted Pair STP Shielded Twisted Pair STP@ 4 Mbps @ 16 Mbps CategoryType Frequency 1000 m 1000 ft Operational Attenuation perSTP Lobe Lengths Mixed STP Cable TypesSingle Mode and Multimode Fiber Optic Cabling Single Mode and Multimode Fiber Optic CablingMax. Lobe Length Max. Drive Distance Type Mbps Total Maximum