Cabletron Systems SEH100TX-22 manual SEH100TX User’s Guide

Page 3

Only qualified personnel should perform installation procedures.

NOTICE

Cabletron Systems reserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult Cabletron Systems to determine whether any such changes have been made.

The hardware, firmware, or software described in this manual is subject to change without notice.

IN NO EVENT SHALL CABLETRON SYSTEMS BE LIABLE FOR ANY INCIDENTAL, INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT NOT LIMITED TO LOST PROFITS) ARISING OUT OF OR RELATED TO THIS MANUAL OR THE INFORMATION CONTAINED IN IT, EVEN IF CABLETRON SYSTEMS HAS BEEN ADVISED OF, KNOWN, OR SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH DAMAGES.

Copyright 1996 by Cabletron Systems, Inc., P.O. Box 5005, Rochester, NH 03866-5005 All Rights Reserved

Printed in the United States of America

Order Number: 9031510-02 December 1996

SPECTRUM, LANVIEW and BRIM are registered trademarks and Element Manager, EPIM, EPIM-100FX, EPIM-100TX, EPIM-100FMB, HubSTACK, MicroMMAC, SEH, and SEHI are trademarks of Cabletron Systems, Inc.

All other product names mentioned in this manual may be trademarks or registered trademarks of their respective companies.

FCC NOTICE

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment uses, generates, and can radiate radio frequency energy and if not installed in accordance with the operator’s manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause interference in which case the user will be required to correct the interference at his own expense.

WARNING: Changes or modifications made to this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Printed on

Recycled Paper

SEH100TX User’s Guide

i

Image 3
Contents 100BASE-T Stackable HUB USER’S Guide Page SEH100TX User’s Guide DOC Notice Cabletron Software Program License Declaration of Conformity Contents Contents Chapter Introduction Using this ManualFollowing conventions are used throughout this document Document ConventionsYour email address Getting HelpRelated Manuals HubSTACK 100BASE-TX HUB with Lanview SEH100TX-22 Chapter SEH Features and OptionsSEH Overview SEH FeaturesRack Mounting Capabilities Stackable CapabilitiesEpim Optional EPIMsChapter Installation Requirements Specifications Cable SpecificationsHubSTACK Interconnect Cable Requirements UTP Cable Specifications Multimode Fiber Optic Cable Specifications Class I Network Network Cable LengthsRJ45 Network Port Pinouts Network Port SpecificationsAgency Approvals Operating SpecificationsImmunity Physical SpecificationsSEH100TX User’s Guide Unpacking the SEH Chapter InstallationHubSTACK 100BASE-TX HUB with Lanview SEH100TX-22 Tabletop or Shelf InstallationScrews Strain-Relief Bracket Rackmount InstallationRack Mounting the SEH Powering Up and Stacking the SEH Powering UP and Stacking the SEHStacking SEH Hubs with an Sehi Repeat steps 3 through 6 until all SEH hubs are connected Stacking Unmanaged SEH Hubs Together Installing AN EpimInstalling an Epim SEH100TX User’s Guide Chapter Connecting to the Network Connecting the SEH100TX-22 to the NetworkConnecting to Network Ports SEH Network Ports Connecting to an EPIM-100TXPosition X crossed over RX+ TX+ Position = Not crossed over Nnecting an EPIM-100FX or EPIM-100FMB EPIM-100FX Port Testing the InstallationSEH100TX User’s Guide Installation Test Chapter TroubleshootingUsing Lanview SEH100TX-22 Epim 1 RCV LED Epim 2 RCV LED Epim Specifications Appendix a Epim InformationEPIM-100TX EPIM-100FX Figure A-3 EPIM-100FMB EPIM-100FMBTable A-2 provides the specifications for the EPIM-100FMB Numerics IndexIndex-2 SEH100TX User’s Guide Power Supply Cord