Cabletron Systems SEH100TX-22 manual DOC Notice

Page 4

Notice

DOC NOTICE

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada.

VCCI NOTICE

This equipment is in the 1st Class Category (information equipment to be used in commercial and/or industrial areas) and conforms to the standards set by the Voluntary Control Council for Interference by Information Technology Equipment (VCCI) aimed at preventing radio interference in commercial and/or industrial areas.

Consequently, when used in a residential area or in an adjacent area thereto, radio interference may be caused to radios and TV receivers, etc.

Read the instructions for correct handling.

CABLETRON SYSTEMS, INC. PROGRAM LICENSE AGREEMENT

IMPORTANT: Before utilizing this product, carefully read this License Agreement.

This document is an agreement between you, the end user, and Cabletron Systems, Inc. (“Cabletron”) that sets forth your rights and obligations with respect to the Cabletron software program (the “Program”) contained in this package. The Program may be contained in firmware, chips or other media. BY UTILIZING THE ENCLOSED PRODUCT, YOU ARE AGREEING TO BECOME BOUND BY THE TERMS OF THIS AGREEMENT, WHICH INCLUDES THE LICENSE AND THE LIMITATION OF WARRANTY AND DISCLAIMER OF LIABILITY. IF YOU DO NOT AGREE TO THE TERMS OF THIS AGREEMENT, PROMPTLY RETURN THE UNUSED PRODUCT TO THE PLACE OF PURCHASE FOR A FULL REFUND.

ii

SEH100TX User’s Guide

Image 4
Contents 100BASE-T Stackable HUB USER’S Guide Page SEH100TX User’s Guide DOC Notice Cabletron Software Program License Declaration of Conformity Contents Contents Using this Manual Chapter IntroductionDocument Conventions Following conventions are used throughout this documentGetting Help Your email addressRelated Manuals Chapter SEH Features and Options HubSTACK 100BASE-TX HUB with Lanview SEH100TX-22SEH Features SEH OverviewStackable Capabilities Rack Mounting CapabilitiesOptional EPIMs EpimCable Specifications Chapter Installation Requirements SpecificationsHubSTACK Interconnect Cable Requirements UTP Cable Specifications Multimode Fiber Optic Cable Specifications Network Cable Lengths Class I NetworkNetwork Port Specifications RJ45 Network Port PinoutsOperating Specifications Agency ApprovalsPhysical Specifications ImmunitySEH100TX User’s Guide Chapter Installation Unpacking the SEHTabletop or Shelf Installation HubSTACK 100BASE-TX HUB with Lanview SEH100TX-22Rackmount Installation Screws Strain-Relief BracketRack Mounting the SEH Powering UP and Stacking the SEH Powering Up and Stacking the SEHStacking SEH Hubs with an Sehi Repeat steps 3 through 6 until all SEH hubs are connected Installing AN Epim Stacking Unmanaged SEH Hubs TogetherInstalling an Epim SEH100TX User’s Guide Connecting the SEH100TX-22 to the Network Chapter Connecting to the NetworkConnecting to Network Ports Connecting to an EPIM-100TX SEH Network PortsPosition X crossed over RX+ TX+ Position = Not crossed over Nnecting an EPIM-100FX or EPIM-100FMB Testing the Installation EPIM-100FX PortSEH100TX User’s Guide Chapter Troubleshooting Installation TestUsing Lanview SEH100TX-22 Epim 1 RCV LED Epim 2 RCV LED Appendix a Epim Information Epim SpecificationsEPIM-100TX EPIM-100FX EPIM-100FMB Figure A-3 EPIM-100FMBTable A-2 provides the specifications for the EPIM-100FMB Index NumericsIndex-2 SEH100TX User’s Guide Power Supply Cord