Cabletron Systems SEH100TX-22 manual Power Supply Cord

Page 51

POWER SUPPLY CORD

The mains cord used with this equipment must be a 2 conductor plus ground type with minimum 0.75 mm square conductors and must incorporate a standard IEC appliance coupler on one end and a mains plug on the other end which is suitable for the use and application of the product and that is approved for use in the country of application.

GERMAN:

Die Netzleitung, die mit diesem Geraet benuetzt wird, soll einen zwei Leiter mit Erdleiter haben, wobei die Leiter mindestens 0.75 mm sind, mit einer normalen IEC Geraetesteckdose an einem Ende und einem Geraetestecker am anderen Ende versehen sind, der fuer den Gebrauch und die Anwendung des Geraetes geeignet und der zum Benuetzen im Lande der Anwendung anerkannt ist.

SPANISH:

El cable principal de la red eléctrica utilizado con este equipo debe tener 2 conductores y 1 toma de tierra con un mínimo de 0.75 mm2 cada uno y necesita tener un aparato de acoplamiento standard IEC en un extremo y un enchufe para el cable principal de la red eléctrica en el otro extremo, lo cual sea adecuado para el uso y applicación del producto y lo cual sea aprobado para uso en el pais de applicación.

FRENCH:

Le cordon d' alimentation reliant cet appareil au secteur doit obligatoirement avoir deux fils conducteurs de 0.75 mm2 minimum et un fil de terre. It doit également être équipé du côté appareil d'une fiche agrée IEC et du côte secteur, d'une prise adaptée à l'usage du produit et aux normes du pays où l'appareil est utilisé.

Image 51
Contents 100BASE-T Stackable HUB USER’S Guide Page SEH100TX User’s Guide DOC Notice Cabletron Software Program License Declaration of Conformity Contents Contents Chapter Introduction Using this ManualFollowing conventions are used throughout this document Document ConventionsYour email address Getting HelpRelated Manuals HubSTACK 100BASE-TX HUB with Lanview SEH100TX-22 Chapter SEH Features and OptionsSEH Overview SEH FeaturesRack Mounting Capabilities Stackable CapabilitiesEpim Optional EPIMsChapter Installation Requirements Specifications Cable SpecificationsHubSTACK Interconnect Cable Requirements UTP Cable Specifications Multimode Fiber Optic Cable Specifications Class I Network Network Cable LengthsRJ45 Network Port Pinouts Network Port SpecificationsAgency Approvals Operating SpecificationsImmunity Physical SpecificationsSEH100TX User’s Guide Unpacking the SEH Chapter InstallationHubSTACK 100BASE-TX HUB with Lanview SEH100TX-22 Tabletop or Shelf InstallationScrews Strain-Relief Bracket Rackmount InstallationRack Mounting the SEH Powering Up and Stacking the SEH Powering UP and Stacking the SEHStacking SEH Hubs with an Sehi Repeat steps 3 through 6 until all SEH hubs are connected Stacking Unmanaged SEH Hubs Together Installing AN EpimInstalling an Epim SEH100TX User’s Guide Chapter Connecting to the Network Connecting the SEH100TX-22 to the NetworkConnecting to Network Ports SEH Network Ports Connecting to an EPIM-100TXPosition X crossed over RX+ TX+ Position = Not crossed over Nnecting an EPIM-100FX or EPIM-100FMB EPIM-100FX Port Testing the InstallationSEH100TX User’s Guide Installation Test Chapter TroubleshootingUsing Lanview SEH100TX-22 Epim 1 RCV LED Epim 2 RCV LED Epim Specifications Appendix a Epim InformationEPIM-100TX EPIM-100FX Figure A-3 EPIM-100FMB EPIM-100FMBTable A-2 provides the specifications for the EPIM-100FMB Numerics IndexIndex-2 SEH100TX User’s Guide Power Supply Cord