Extron electronic CVEQ 100 Series, A-4, A-2, A-3 Preparing the Cveq 100 for through-desk mounting

Page 11

Installation

Preparing the CVEQ 100 for through-desk mounting

1. If rubber feet were previously attached to the bottom of the unit, remove them.

2. Attach the mounting brackets to the CVEQ 100 with the provided machine screws as shown in the previous figure.

3. Hold the unit with the attached brackets against the underside of the table or other furniture. On the mounting surface, mark the location of the bracket’s screw holes.

4. Mark the opening on the desk using a soft pencil. The opening should be slightly larger than the dimensions of the unit.

Use an appropriate saw to cut the opening. If needed, enlarge the hole with a file or sandpaper.

5. Drill ³⁄³²" (2 mm) diameter pilot holes, ¼" (6.3 mm) deep in

the mounting surface at the marked screw locations.

6. Insert #8 wood screws into the four pilot holes. Tighten each screw into the mounting surface until slightly less than ¼" of the screw head protrudes.

7. Align the mounting screws with the slots in the brackets and place the unit against the surface, with the screws through the bracket slots.

8. Slide the unit slightly forward or back, then tighten all four screws to secure it in place.

9. Attach input and output cables. See chapter 3.

Back of the rack mounting (SVEQ 100 only)

The SVEQ 100 can be mounted to the rear of a rack using the Extron VersaTools MBB 100 back of the rack mounting kit (part #70-367-01). The kit allows the product to be vertically mounted to the front or rear rack supports and facing either towards the front or the rear of the rack.

Using the MBB 100 back of the rack kit

1. If necessary, remove the feet from the bottom of the line driver.

2. Remove two screws from one side of the unit. Retain the screws for possible later reassembly without the bracket.

3. Attach one bracket to the side of the unit using the longer screws included in the kit.

4. Repeat steps 2 and 3 on the other side of the unit.

5. Mount the unit to the rack using the two included rack screws (see the following illustration). The SVEQ 100 can be vertically mounted facing in either direction. See the following diagram.

7. Attach input and output cables. See chapter 3 for details on wiring.

NOnly VersaTools products and most IP Link products can be mounted using the back of the rack mounting kit.

2-8

CVEQ 100 and SVEQ 100 Series • Installation

CVEQ 100 and SVEQ 100 Series • Installation

2-9

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Cveq 100 Series Sveq 100 Series Extron’s Warranty PrecautionsFCC Class a Notice 安全须知 中文Step Quick Start Guide CVEQ/SVEQ 100 SeriesTable of Contents Cveq 100 and Sveq 100 Series Table of Contents, cont’dOne IntroductionIntroduction InstallationFeatures TwoApplication Examples InstallationCveq 100 and Sveq 100 Series Installation Installing the Cveq 100/SVEQ Installation InstructionsFurniture mounting through-desk Cveq 100 only Furniture mounting under-deskBack of the rack mounting Sveq 100 only Preparing the Cveq 100 for through-desk mountingInstalling the Cveq 100 AAP/SVEQ 100 AAP Installation, cont’dMounting in a European cable channel Installing the Cveq 100 MAAP/SVEQ 100 MaapMounting in an external wall box Mounting the line driver Installing the Cveq 100 D/SVEQ 100 DPreparing the site and installing the wall box If the image does not appear or there is no sound Testing and troubleshootingIf the image is not displayed correctly Operation ThreeCveq 100 and Sveq 100 Series Operation Front Panel Features and OperationOperation Video Pinout Table Cveq 100 Rear Panel Sveq 100 AAP Rear Connectors Rear Panel Features and OperationSveq 100 D Rear Panel Operation, cont’dScrew connector. See the following wiring diagrams Power supply wiringReplacing the Decora Faceplate Cveq 100 D and Sveq 100 D Gain adjustment controlEqualization EQ adjustment control AAppendix a Specifications, Part Numbers AccessoriesSpecifications Specifications, Part Numbers, and AccessoriesGeneral Specifications, Part Numbers, Accessories, cont’dAudio output Included Parts Included parts Replacement Part numberDescription Part number Optional AccessoriesCveq 100 and Sveq 100 Series Specifications and Parts A-11 Accessory Part numberAppendixBB Dimensions and TemplateCut-out Template Dimensions and TemplateDecora Models Dimensions Dimensions and Template
Top Page Image Contents