Extron electronic A-3, CVEQ 100 Series, A-4, A-2 Quick Start Guide CVEQ/SVEQ 100 Series, Step

Page 4

Quick Start Guide — CVEQ/SVEQ 100 Series

CInstallation and service must be performed by authorized personnel only. These line drivers must be used with UL approved, grounded electrical boxes.

To install and set up the line driver, follow these steps and see the appropriate sections of this manual for details.

Step 1

Turn the input and output devices off and unplug their power cords.

Verify that the line driver is disconnected from the power source before proceeding.

Step 2

Attach output cables to the rear panel of the line driver and to the output devices. See "Rear Panel Features and Operation" in chapter 3 for details.

Step 3

Attach input cables from the input devices to the line driver’s front panel input connectors. See "Front Panel Features and Operation" in chapter 3.

Step 4

Connect power cords (see page 3-11) and turn on the output devices (projector/monitor,­ speakers) and input devices.

Step 5

The picture should appear and sound should be audible. If not, ensure that all devices are plugged in and receiving power. Check the cabling, make adjustments as needed. For further details, see "Testing and troubleshooting" in chapter 2.

Step 6

While watching the display, adjust the video gain and equalization by using the rotary gain and equalization (EQ) control potentiometers. An oscilloscope can be used to achieve a more precise adjustment. See “Gain adjustment control" and "Equalization (EQ) adjustment control” in chapter 3 for details.

Make all adjustments using an Extron Tweeker or small screwdriver. If using very short output cables, set all potentiometers to the default setting (the arrow on the control pointing to the dot beside it).

CVEQ 100 Series

SVEQ 100 Series

CVEQ 100 and SVEQ 100 Series • Quick Start Guide QS-1

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Cveq 100 Series Sveq 100 Series Precautions Extron’s Warranty安全须知 中文 FCC Class a NoticeQuick Start Guide CVEQ/SVEQ 100 Series StepTable of Contents Table of Contents, cont’d OneIntroduction Cveq 100 and Sveq 100 SeriesInstallation FeaturesTwo IntroductionCveq 100 and Sveq 100 Series Installation InstallationApplication Examples Installation Instructions Installing the Cveq 100/SVEQFurniture mounting under-desk Furniture mounting through-desk Cveq 100 onlyPreparing the Cveq 100 for through-desk mounting Back of the rack mounting Sveq 100 onlyInstallation, cont’d Installing the Cveq 100 AAP/SVEQ 100 AAPMounting in an external wall box Installing the Cveq 100 MAAP/SVEQ 100 MaapMounting in a European cable channel Preparing the site and installing the wall box Installing the Cveq 100 D/SVEQ 100 DMounting the line driver If the image is not displayed correctly Testing and troubleshootingIf the image does not appear or there is no sound Three OperationOperation Front Panel Features and OperationCveq 100 and Sveq 100 Series Operation Video Pinout Table Rear Panel Features and Operation Cveq 100 Rear Panel Sveq 100 AAP Rear ConnectorsOperation, cont’d Sveq 100 D Rear PanelPower supply wiring Screw connector. See the following wiring diagramsEqualization EQ adjustment control Gain adjustment controlReplacing the Decora Faceplate Cveq 100 D and Sveq 100 D Specifications, Part Numbers Accessories AAppendix aSpecifications, Part Numbers, and Accessories SpecificationsAudio output Specifications, Part Numbers, Accessories, cont’dGeneral Included parts Replacement Part number Included PartsOptional Accessories Description Part numberAccessory Part number Cveq 100 and Sveq 100 Series Specifications and Parts A-11Dimensions and Template AppendixBBDecora Models Dimensions Dimensions and TemplateCut-out Template Dimensions and Template
Top Page Image Contents