Extron electronic A-2, SVEQ 100 Series, CVEQ 100 Series, A-4, A-3 user manual Video Pinout Table

Page 18

Operation

A Power indicator LED — This LED lights:

•Amber when the line driver is receiving full power (this applies to all models except the CVEQ 100 and SVEQ 100, which light green instead).

•Green when the line driver is receiving a video signal (this only applies to the D, AAP, and MAAP models).

ÇGain potentiometer (CVEQ 100 and luma of SVEQ 100) — Use a small screwdriver to rotate this potentiometer to adjust the CVEQ 100's gain and the SVEQ 100's luminance gain when the line driver is connected to long output cables. The adjustment range is -1 dB to +3 dB. The default is unity (the dot position). See "Gain adjustment control" in this chapter.

ÉGain potentiometer (chroma of SVEQ 100) — Use a small screwdriver to rotate this potentiometer to adjust the chroma gain when the SVEQ 100 is connected to long output cables. The adjustment range is 0 dB to +10 dB. The default is unity (the dot position). See "Gain adjustment control" in this chapter.

C

Equalization (EQ) potentiometer — Use a small screwdriver

 

to rotate this potentiometer to adjust equalization when the line

 

driver is connected to long output cables. The adjustment range

 

is 0 dB to +7 dB. The default is set to 0 dB (the dot position). See

 

"Equalization (EQ) adjustment control" in this chapter.

D

Video input connector — Connect a composite video input

 

source to this RCA connector.

E

S-video input connector — Connect an S-video input source to

 

this 4-pin mini DIN connector. See the following pinout table.

 

3

4

1 2

S-video Pinout Table

PIN

NAME

DESCRIPTION

 

 

 

1

GND

Ground (Y)

 

 

 

2

GND

Ground (C)

 

 

 

3

Y

Luminance

 

 

 

4

C

Chrominance

 

 

 

F

Audio input connectors — Connect an unbalanced stereo audio

 

source to these left (L) and right (R) RCA connectors. Wire the

 

male connector as shown in the following illustration.

 

Tip (+)

 

Sleeve ( )

3-4

CVEQ 100 and SVEQ 100 Series • Operation

CVEQ 100 and SVEQ 100 Series • Operation

3-5

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Cveq 100 Series Sveq 100 Series Precautions Extron’s Warranty安全须知 中文 FCC Class a NoticeQuick Start Guide CVEQ/SVEQ 100 Series StepTable of Contents Introduction Table of Contents, cont’dOne Cveq 100 and Sveq 100 SeriesTwo InstallationFeatures IntroductionInstallation Cveq 100 and Sveq 100 Series InstallationApplication Examples Installation Instructions Installing the Cveq 100/SVEQFurniture mounting under-desk Furniture mounting through-desk Cveq 100 onlyPreparing the Cveq 100 for through-desk mounting Back of the rack mounting Sveq 100 onlyInstallation, cont’d Installing the Cveq 100 AAP/SVEQ 100 AAPInstalling the Cveq 100 MAAP/SVEQ 100 Maap Mounting in an external wall boxMounting in a European cable channel Installing the Cveq 100 D/SVEQ 100 D Preparing the site and installing the wall boxMounting the line driver Testing and troubleshooting If the image is not displayed correctlyIf the image does not appear or there is no sound Three OperationFront Panel Features and Operation OperationCveq 100 and Sveq 100 Series Operation Video Pinout Table Rear Panel Features and Operation Cveq 100 Rear Panel Sveq 100 AAP Rear ConnectorsOperation, cont’d Sveq 100 D Rear PanelPower supply wiring Screw connector. See the following wiring diagramsGain adjustment control Equalization EQ adjustment controlReplacing the Decora Faceplate Cveq 100 D and Sveq 100 D Specifications, Part Numbers Accessories AAppendix aSpecifications, Part Numbers, and Accessories SpecificationsSpecifications, Part Numbers, Accessories, cont’d Audio outputGeneral Included parts Replacement Part number Included PartsOptional Accessories Description Part numberAccessory Part number Cveq 100 and Sveq 100 Series Specifications and Parts A-11Dimensions and Template AppendixBBDimensions and Template Decora Models DimensionsCut-out Template Dimensions and Template
Top Page Image Contents