Extron electronic manual Installation, cont’d, Connecting the SWP123 Switcher

Page 14

Installation, cont’d

14Serial Port A (RS-232/RS-422/RS-485 connector) — A 3.8 mm, 5-pole captive screw connector for input from a computer or third-party controller using Serial Control Protocol commands or ICS100 Control Software to remotely control the switcher.

Rx+

Rx-

Tx+

Tx-

Gnd

Rx+

Rx-

Tx+

Tx-

Gnd

RS-232/422/485

5-pole captive screw connector/socket

15Composite Video output — One female BNC connector for composite video output

16Composite Video input — Four female BNC connectors for composite video input

17S-video output — One 4-pin mini DIN connector for S-video output

18S-video input — Four 4-pin mini DIN connectors for S-video input

19VGA video output — One female VGA connector for VGA video output

20VGA video input — Four female VGA connectors for VGA video input

Connecting the SWP123 Switcher

The SWP123 Presentation Switcher can be connected to as many as 12 input devices simultaneously and to up to 3 outputs simultaneously. Follow the steps below and see the installation example in figure 2-3.

1

2

3

4

5

6

7

If the switcher is to be mounted, see Mounting the Switcher, earlier in this chapter.

Turn off power to the switcher and all other devices that will be connected.

Using inputs 1, 2, 3, and 4 of the VGA, S-video, and Video (composite) groups, attach up to 12 video input devices to the switcher.

Connect output display devices to the switcher using VGA, S-video, or Composite Video outputs.

Connect up to 12 stereo audio sources to audio inputs 1, 2, 3, and 4 of the VGA, S-video, or Composite Video audio groups. See Audio input and output later in this chapter.

If using a computer or host controller for remote control, connect the host’s RS-232 cable to the 3.8 mm, 5-pole captive screw serial port (Serial Port A) of the switcher. For an RS-232/RS-422/RS-485 pinout table and DIP switch settings, see Remote Control Port (RS-232/RS-422/RS-485)in chapter 5.

Power up the input and output devices, then connect power to the switcher.

2-4 SWP123 Presentation Switcher • Installation

Image 14

Contents Presentation Switcher SWP123Consignes de Sécurité Français PrecautionsSafety Instructions English Sicherheitsanleitungen DeutschRack mounting the SWP123 SWP123 Presentation Switcher Quick Start QS-1Quick Start SWP123 QS-2 SWP123 Presentation Switcher Quick Start Quick Start SWP123, cont’dTable of Contents Table of Contents, cont’d One IntroductionSWP123 Presentation Switcher Introduction About the SWP123 Presentation SwitcherSWP123 Switcher Features IntroductionSWP123 Presentation Switcher Introduction Introduction, cont’d Installation TwoSWP123 Presentation Switcher Installation InstallationMounting the Switcher Tabletop useRear Panel Connectors Rear panel of the SWP123Installation, cont’d Connecting the SWP123 SwitcherConnecting the unbalanced audio input Audio input and outputConnecting the unbalanced audio output Connecting the balanced audio outputOperation MVP 104GX InstallationThree Operation Front Panel FeaturesSWP123 Presentation Switcher Operation Video/Audio Select groupsSelecting A/V inputs to output Miscellaneous controls and featuresFront Panel Operation Blanking the output from a groupMicrophone controls Operation, cont’dMaster Audio functions Decoder Loop Function Wiring the decoder loop+24V Phantom Power switch This page was intentionally left blank MVP 104 Operation FourWindows-Based Control Program Specifying your switcher model Installing the Windows-based ICS100 Control SoftwareUsing the Software Windows-Based Control Program, cont’dUsing the Control Panel Defining input icons and labelsSelecting a new input Adjusting the Master Audio or Microphone audio levelEnabling audio-follow-video switching Blanking the output of a groupEnabling/disabling front panel control Setting audio gain input to Master Audio outputUsing Terminal Comm ICS100 Control Program Help Resetting the unitSWP123 Presentation Switcher Windows-Based Control Program MVP 104 Windows Control Program Remote ControlFive DIP switch settings SWP123 Presentation Switcher Remote ControlAddressing commands Host-to-Switcher CommunicationsUsing the command tables Remote Control, cont’d Setup commandsSwitching commands Volume commands Mute/un-muteRamp volume level Adjust volume level-rightSet volume level-right Stop volume rampRemote Control from a Network Enabling remote control of the switcher over a networkConfiguring the server local PC Configuring the client remote PCStopping communication Adjusting response time10 SWP123 Presentation Switcher Remote Control CTL120-3 IR Remote Control Switching input devicesResetting the component code 12SWP123 Presentation Switcher Remote ControlMVP 104 Programmer’s Guide SpecificationsAAppendix Specifications SWP123 Presentation Switcher SpecificationsSWP123 Presentation Switcher Specifications Audio masterSpecifications, cont’d Master audio outputBAppendix Reference InformationUpdating the Firmware SWP123 Presentation Switcher Reference InformationReference Information Part Numbers SWP123 switcher part numbersOptional accessories CablesExtron Part Part number BNC-5 Mini HR Cable Reference Information, cont’dPre-cut cables FCC Class a Notice Extron’s Warranty Extron Electronics, USA