Gigabyte 8S648FXP-RZ-C user manual USB Controller, USB Legacy Support, SiS Serial ATA Controller

Page 26

English

USB Controller

Enabled

Enable USB Controller. (Default value)

Disabled

Disable USB Controller.

USB Legacy Support

When USB keyboard or mouse is installed, please set at Enabled.

Enabled

Enable USB keyboard or mouse support.

Disabled

Disable USB keyboard or mouse support. (Default value)

SiS Serial ATA Controller

Enabled

Enable onboard SiS serial ATA Controller. (Default value)

Disabled

Disable this function.

SiS Serial ATA Mode

IDE

Set onboard Serial ATA function as IDE.

RAID

Set onboard Serial ATA function as RAID. (Default value)

Onboard Serial Port 1

Auto

BIOS will automatically setup the port 1 address.

3F8/IRQ4

Enable onboard Serial port 1 and address is 3F8. (Default value)

2F8/IRQ3

Enable onboard Serial port 1 and address is 2F8.

3E8/IRQ4

Enable onboard Serial port 1 and address is 3E8.

2E8/IRQ3

Enable onboard Serial port 1 and address is 2E8.

Disabled

Disable onboard Serial port 1.

Onboard Serial Port 2

Auto

BIOS will automatically setup the port 2 address.

3F8/IRQ4

Enable onboard Serial port 2 and address is 3F8.

2F8/IRQ3

Enable onboard Serial port 2 and address is 2F8. (Default value)

3E8/IRQ4

Enable onboard Serial port 2 and address is 3E8.

2E8/IRQ3

Enable onboard Serial port 2 and address is 2E8.

Disabled

Disable onboard Serial port 2.

Onboard Parallel port

Disabled

Disable onboard LPT port.

378/IRQ7

Enable onboard LPT port and address is 378/IRQ7. (Default value)

278/IRQ5

Enable onboard LPT port and address is 278/IRQ5.

3BC/IRQ7

Enable onboard LPT port and address is 3BC/IRQ7.

Parallel Port Mode

SPP

Using Parallel port as Standard Parallel Port.

EPP

Using Parallel port as Enhanced Parallel Port.

ECP

Using Parallel port as Extended Capabilities Port. (Default value)

ECP+EPP

Using Parallel port as ECP & EPP mode.

ECP Mode Use DMA

3

Set ECP Mode Use DMA to 3. (Default value)

1

Set ECP Mode Use DMA to 1.

8S648FXP-RZ Series Motherboard

- 26 -

Image 26
Contents 8S648FXP-RZ / 8S648FXP-RZ-C Motherboard 8S648FXP-RZ Installing the motherboard to the chassis Preparing Your ComputerTable of Contents Features Summary Introduction8S648FXP-RZ Series Motherboard Layout Cdin P4 TitanBlock Diagram Step Hardware Installation ProcessInstall the Central Processing Unit CPU CPU Installation Install Memory Modules Install AGP Card Install I/O Peripherals Cables15 IR CdinFUSB1 / FUSB2 17 BATATX12V / ATX Power Connector Cpufan / Sysfan Cooler Fan Power ConnectorSATA0 / SATA1 Serial ATA Connector FDD FDD ConnectorIDE1 / IDE2 IDE1 / IDE2 Connector Fpanel 2 x 10 pins Connector Faudio Front Audio Connector Spdifio Spdif In/Out ConnectorFUSB1 / FUSB2 Front USB Connector Surcen Surround Center ConnectorCdin CD In Connector BAT Battery Clrcmos Clear CmosMain Menu Main Menu For example Bios Ver. E10Status Page Setup Menu / Option Page Setup Menu PnP/PCI Configuration Advanced Bios FeaturesPower Management Setup Load Fail-Safe DefaultsTime Standard Cmos FeaturesDate IDE Channel 0 Master, Slave / IDE Channel 1 Master, SlaveHalt on Floppy 3 Mode Support for Japan AreaDrive a / Drive B MemoryFirst / Second / Third Boot Device Advanced Bios FeaturesHard Disk Boot Priority Boot Up Floppy SeekLimit Cpuid Max. to Password CheckCPU Hyper-Threading Init Display FirstIntegrated Peripherals ECP Mode Use DMA SiS Serial ATA ModeParallel Port Mode USB ControllerPower Management Setup Resume by Alarm Power On by KeyboardPower On by Mouse Power LED in S1 statePCI 1/PCI 5 IRQ Assignment PnP/PCI ConfigurationsPCI 4 IRQ Assignment PCI 2 IRQ AssignmentCurrent Voltage V Vcore / DDR2.5V / +3.3V / +12V Current CPU TemperaturePC Health Status Current CPU/SYSTEM FAN Speed RPMMB Intelligent TweakerM.I.T Top Performance Load Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password ConfigurationsEnter PasswordSave & Exit Setup Exit Without SavingEnglish Install Drivers Pictures below are shown in Windows XPItem Description Contact Us Taiwan HeadquartersChina Shanghai