Gigabyte 8S648FXP-RZ-C user manual FDD FDD Connector, IDE1 / IDE2 IDE1 / IDE2 Connector

Page 14

English

5) FDD (FDD Connector)

The FDD connector is used to connect the FDD cable while the other end of the cable connects to the FDD drive. The types of FDD drives supported are: 360KB, 720KB, 1.2MB, 1.44MB and 2.88MB. Please connect the red power connector wire to the pin1 position.

2

34

1

33

6) IDE1 / IDE2 (IDE1 / IDE2 Connector)

An IDE device connects to the computer via an IDE connector. One IDE connector can connect to one IDE cable, and the single IDE cable can then connect to two IDE devices (hard drive or optical drive). If you wish to connect two IDE devices, please set the jumper on one IDE device as Master and the other as Slave (for information on settings, please refer to the instructions located on the IDE device).

4039

21

IDE2 IDE1

7) SATA0 / SATA1 (Serial ATA Connector)

Serial ATA can provide 150MB/s transfer rate. Please refer to the BIOS setting for the Serial ATA and install the proper driver in order to work properly.

 

 

 

Pin No.

Definition

7

 

1

1

GND

 

2

TXP

 

SATA1

 

 

 

3

TXN

 

 

 

7

 

1

4

GND

 

5

RXN

 

SATA0

 

 

 

6

RXP

 

 

 

 

 

 

7

GND

For more detailed Serial ATA RAID setup information, please visit our website at http:\\www.gigabyte.com.tw.

8S648FXP-RZ Series Motherboard

- 14 -

Image 14
Contents 8S648FXP-RZ / 8S648FXP-RZ-C Motherboard 8S648FXP-RZ Installing the motherboard to the chassis Preparing Your ComputerTable of Contents Features Summary Introduction8S648FXP-RZ Series Motherboard Layout Cdin P4 TitanBlock Diagram Step Hardware Installation ProcessInstall the Central Processing Unit CPU CPU Installation Install Memory Modules Install AGP Card Install I/O Peripherals Cables15 IR CdinFUSB1 / FUSB2 17 BATATX12V / ATX Power Connector Cpufan / Sysfan Cooler Fan Power ConnectorSATA0 / SATA1 Serial ATA Connector FDD FDD ConnectorIDE1 / IDE2 IDE1 / IDE2 Connector Fpanel 2 x 10 pins Connector Faudio Front Audio Connector Spdifio Spdif In/Out ConnectorFUSB1 / FUSB2 Front USB Connector Surcen Surround Center ConnectorCdin CD In Connector BAT Battery Clrcmos Clear CmosMain Menu Main Menu For example Bios Ver. E10Status Page Setup Menu / Option Page Setup Menu PnP/PCI Configuration Advanced Bios FeaturesPower Management Setup Load Fail-Safe DefaultsTime Standard Cmos FeaturesDate IDE Channel 0 Master, Slave / IDE Channel 1 Master, SlaveHalt on Floppy 3 Mode Support for Japan AreaDrive a / Drive B MemoryFirst / Second / Third Boot Device Advanced Bios FeaturesHard Disk Boot Priority Boot Up Floppy SeekLimit Cpuid Max. to Password CheckCPU Hyper-Threading Init Display FirstIntegrated Peripherals ECP Mode Use DMA SiS Serial ATA ModeParallel Port Mode USB ControllerPower Management Setup Resume by Alarm Power On by KeyboardPower On by Mouse Power LED in S1 statePCI 1/PCI 5 IRQ Assignment PnP/PCI ConfigurationsPCI 4 IRQ Assignment PCI 2 IRQ AssignmentCurrent Voltage V Vcore / DDR2.5V / +3.3V / +12V Current CPU TemperaturePC Health Status Current CPU/SYSTEM FAN Speed RPMMB Intelligent TweakerM.I.T Top Performance Load Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password ConfigurationsEnter PasswordSave & Exit Setup Exit Without SavingEnglish Install Drivers Pictures below are shown in Windows XPItem Description Contact Us Taiwan HeadquartersChina Shanghai