Gigabyte 8S648FXP-RZ-C user manual MB Intelligent TweakerM.I.T

Page 31

MB Intelligent Tweaker(M.I.T.)

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software

MB Intelligent Tweaker(M.I.T.)

 

Configure DRAM Timing

[Auto]

 

 

 

Item Help

x

CAS Latency Setting

2.5T

 

 

Menu Level`

x DRAM RAS Active Time

9T

 

 

 

 

x DRAM RAS Precharge Time

5T

 

 

[AUTO]

x DRAM RAS to CAS Delay

5T

 

 

Configure DRAM

 

CPU Clock Ratio

[21X]

 

 

Timing automatically

 

Linear Frequency Control

[Disabled]

 

 

 

 

x

CPU Clock (MHz)

133

 

 

[Manual]

x

DRAM Clock (MHz)

AUTO

 

 

Configure DRAM

 

AGP/PCI Clock Control

[AUTO]

 

 

Timing by manual

x

AGP Clock (MHz)

66

 

 

 

 

x

PCI Clock (MHz)

33

 

 

Warning: Wrong DRAM

 

DRAM Voltage Control

[Normal]

 

 

Timing may make

 

 

 

 

 

 

system can't boot.

 

 

 

 

 

 

Clear CMOS to overcome

 

 

 

 

 

 

wrong Timing issue.

 

 

 

 

 

 

 

KLJI: Move

Enter: Select

+/-/PU/PD: Value

F10: Save

ESC: Exit

F1: General Help

 

F5: Previous Values

F6: Fail-Save Defaults

F7: Optimized Defaults

 

 

 

 

 

 

 

 

Incorrect using these features may cause your system broken. For power end-user use only.

Configure DRAM Timing

Auto

Configure the DRAM Timing automatically. (Default value)

Manual

Configure the DRAM Timing manually.

CAS Latency Setting

Set CAS Latency manually. Options are: 2T, 2.5T, 3T, and Auto. (Default value: 2.5T)

DRAM RAS Active Time

Set DRAM RAS Active Time manually. Options are: 6T, 7T, 5T, 4T, 8T and 9T. (Default value: 9T)

DRAM RAS Precharge Time

Set DRAM RAS Precharge Time manually. Options are: 3T, 2T, 4T, and 5T. (Default value:5T)

DRAM RAS to CAS Delay

Set DRAM RAS to CAS Delay Time manually. Options are: 3T, 2T, 4T, and 5T. (Default value:5T)

CPU Clock Ratio

This setup option will automatically assign by CPU detection.

The option will display "Locked" and read only if the CPU ratio is not changeable.

Linear Frequency Control

Disabled

Disable this function. (Default value)

Enabled

Enable this function.

CPU Clock (MHz)

100MHz ~ 355MHz Set CPU Host Clock from 100MHz to 355MHz.

If you use a 400MHz FSB Pentium 4 processor, please set "CPU Clock" to 100MHz. If you use a 533 MHz FSBPentium 4 processor, please set "CPU Clock" to 133MHz. If you use a 800MHz FSB Pentium 4 processor, please set "CPU Clock" to 200MHz.

English

- 31 -

BIOS Setup

Image 31
Contents 8S648FXP-RZ / 8S648FXP-RZ-C Motherboard 8S648FXP-RZ Preparing Your Computer Installing the motherboard to the chassisTable of Contents Introduction Features SummaryCdin P4 Titan 8S648FXP-RZ Series Motherboard LayoutBlock Diagram Install the Central Processing Unit CPU Hardware Installation ProcessStep CPU Installation Install Memory Modules Install I/O Peripherals Cables Install AGP Card17 BAT CdinFUSB1 / FUSB2 15 IRCpufan / Sysfan Cooler Fan Power Connector ATX12V / ATX Power ConnectorIDE1 / IDE2 IDE1 / IDE2 Connector FDD FDD ConnectorSATA0 / SATA1 Serial ATA Connector Fpanel 2 x 10 pins Connector Spdifio Spdif In/Out Connector Faudio Front Audio ConnectorCdin CD In Connector Surcen Surround Center ConnectorFUSB1 / FUSB2 Front USB Connector Clrcmos Clear Cmos BAT BatteryStatus Page Setup Menu / Option Page Setup Menu Main Menu For example Bios Ver. E10Main Menu Load Fail-Safe Defaults Advanced Bios FeaturesPower Management Setup PnP/PCI ConfigurationIDE Channel 0 Master, Slave / IDE Channel 1 Master, Slave Standard Cmos FeaturesDate TimeMemory Floppy 3 Mode Support for Japan AreaDrive a / Drive B Halt onBoot Up Floppy Seek Advanced Bios FeaturesHard Disk Boot Priority First / Second / Third Boot DeviceInit Display First Password CheckCPU Hyper-Threading Limit Cpuid Max. toIntegrated Peripherals USB Controller SiS Serial ATA ModeParallel Port Mode ECP Mode Use DMAPower Management Setup Power LED in S1 state Power On by KeyboardPower On by Mouse Resume by AlarmPCI 2 IRQ Assignment PnP/PCI ConfigurationsPCI 4 IRQ Assignment PCI 1/PCI 5 IRQ AssignmentCurrent CPU/SYSTEM FAN Speed RPM Current CPU TemperaturePC Health Status Current Voltage V Vcore / DDR2.5V / +3.3V / +12VMB Intelligent TweakerM.I.T Top Performance Load Optimized Defaults Load Fail-Safe DefaultsConfigurationsEnter Password Set Supervisor/User PasswordExit Without Saving Save & Exit SetupEnglish Pictures below are shown in Windows XP Install DriversItem Description Taiwan Headquarters Contact UsChina Shanghai