ATTO Technology S-Class manual SledFaultLED, SMARTData, Temperature, VirtualDriveInfo

Page 53

SledFaultLED

Changes the state of the selected sled LED to the indicated state. Enter sled number (1-12) (all)

Default: off

Set syntax: set SledFaultLED [all123456789101112] [on off]

SMARTData

Displays the current SMART Data (Self-Monitoring Analysis and Reporting Technology) for the specified drive.

Immediate command: SMARTData [Sled#] [Drive#]

Temperature

Returns the current internal temperature of this Diamond Storage Array in degrees Celsius. The value is read only.

Get syntax: get Temperature

VirtualDriveInfo

Displays the named Virtual Drive definitions.

Immediate command: VirtualDriveInfo [active planned] [Virtual Drive ID]

42 Diagnostic CLI commands

Image 53

Contents

Diamond Storage Array Class Page Page Contents In-band CLI Over the Fibre Channel Serial Port Configuration Commands Configuring Drives RAID Interleave Parameters Appendix E Warranty Viii Appendix D Specifications ViiAtto Technology, Inc PrefacePage Diamond Storage Array Product Overview Diamond Storage Array featuresScsi model Fibre Channel modelDiamond Storage Array Technical Overview Adxt Powers ATA to New LevelsATA Interface Engine AIE The interface to each Physical setup Installation InstructionsSet up the Ethernet connection Connect to EthernetSet up RAID configuration Rack mount ComponentsFloor model Components Spaced rail pairs in some rackmount cabinets Physical Set UpRack mount cabinets with stationary shelf or tray Sliding shelf or tray type systems should neverGeneral instructions Manual configuration Connecting a Fibre Channel ArrayAutoconfiguration Fibre Channel connections To connect a Scsi array Connecting a Scsi ArrayBus speed, MB/sec Bus width Max. bus lengths Max. device BitsScsi connections Physical numbering Determining Drive and Sled DesignationsLogical numbering Numbering conventionsUnique serial number for each LUN ExamplesRAID Level 10 QuickRAID10 The QuickRAID10 RAID Level 5 QuickRAID5 with a fullyCommand Line Interface Accessing the ArrayAtto ExpressNAV RS-232 portSnmp Initiator Host Diamond Array In-band CLI Over the Fibre ChannelDetails Initiator/Host Diamond Storage Array Invalidparameterincdb will be returnedSerial Port Access Serial port access To connect to the Ethernet port Ethernet Access Telnet and Snmp ProtocolsTo use Telnet To use SnmpTraps are generated for the following situations Type SaveConfiguration restart to reboot the arrayBrowser compatibility Atto ExpressNAV Browser-based InterfaceOpening an ExpressNAV session Navigating ExpressNAVInformation Sidebar ExpressNAV Pages Clear Data ConfigurationLogical Units RebuildCommand Line Interface actions and responses Command Line Interface Use and GuidancePage Command Defaults Example Summary of CLI CommandsCommand Defaults Example General Use Commands General CLI commands Ethernet Commands TelnetUsername TelnetPasswordTelnetTimeout Fibre Channel Configuration Commands FcPortList FcPortInfo FcPortName FcWWNameSerialPortBaudRate Serial Port Configuration CommandsSerialPortHandshake SerialPortEchoSerial port CLI commands Diagnostic Commands Temperature SledFaultLEDSMARTData VirtualDriveInfoFcScsiBusyStatus Maintenance CommandsMaxEnclTempAlrm MinEnclTempAlrmMaintenance CLI commands Drive Configuration Commands IdeTransferRate DriveWipeLUNState QuickRAID0RAID5ClearData RestoreModePagesRAID5ClearDataStatus RAIDInterleaveExamples, refer to Information Commands Results on RAID Level Configuring DrivesJbod Just a Bunch of Disks Enhancing performance InterleaveHot Spare sleds Jbod To set up the Jbod configurationJbod Sled-based versus disk-based RAID LevelLUNs virtual drive numbers To remove RAID Level 0 groupsPage Page Type SaveConfiguration To set up RAID Level 1 groupsType SaveConfiguration Storage Management To remove RAID groupsType set QuickRAID 1 To set up RAID Level 1 with Hot Spare sledsTo set up one RAID Level 5 group with one Hot Spare sled Configuring a fully-populated arrayTo set up RAID Level 5 groups Type set QuickRAID5 2 Type SaveConfiguration Restart Type set QuickRAID5 1 Type SaveConfiguration RestartTo set up two RAID Level 5 groups with two Hot Spare sleds LUN Removing RAID groups Type set QuickRAID5 ALL Type SaveConfiguration RestartType set QuickRAID10 0 1 2 To set up RAID Level 10 groupsType set QuickRAID10 1 Type SaveConfiguration Restart To set up RAID Level 10 with Hot Spare sledsRebuilding RAID Configurations To synchronize mirrored drives manually Set AutoRebuild disabled saveconfiguration restartTo change the RAID Interleave parameter RAID Interleave ParametersRAID interleave Hardware Maintenance Maintenance Disk drives Hot Swap Operating InstructionsBlower assemblies Power suppliesTo replace a blower assembly Optional Hot Spare Sled Type set QuickRAID1 Type SaveConfiguration RestartVirtual Drive Hot Spare sleds To set up two RAID Level 5 groups with Hot Spare sledsCopying Drives ProcedureCopy drives Updating Firmware Updating firmware using the RS-232 serial portType put ....ima Cd c\diamond\flashSystem Monitoring and Reporting System fault LED and error codes Power supply monitoringNumber of blinks Command Line Interface messages TroubleshootingWindows 2000 special instructions Error messages Specific situations and suggestions Type FirmwareRestart If LUNs do not display on the hostDefault Resetting DefaultsFactory Default To return to Default settingsCommand Default Reset if default Reset during Chosen Fibre Channel FeatureDriveInfo sled ID drive ID Appendix B Information Commands ResultsV80DTESC Info allLunInfo LUNInfo LUNVirtualDriveInfo VirtualDriveInfo active planned Virtual Drive IDRadio and television interference Safety compliances EMC specificationsEnvironmental and physical Rack mount dimensionsFloor mount dimensions Contact Atto Technology, Inc Manufacturer limited warranty