ATTO Technology S-Class manual Examples, refer to Information Commands Results on

Page 59

SledFaultLED

Changes the state of the selected sled LED to the indicated state.

Choices: enter sled number 1-12 or all, on or off

Default: off

Set syntax: set SledFaultLED [allsled number] [on off]

VirtualDriveInfo

Displays the named Virtual Drive definitions. For

examples, refer to Information Commands Results on page ii.

Immediate command: VirtualDriveInfo [activeplanned] [Virtual Drive ID]

48 Configure drives with CLI commands

Image 59

Contents

Diamond Storage Array Class Page Page Contents In-band CLI Over the Fibre Channel Serial Port Configuration Commands Configuring Drives RAID Interleave Parameters Appendix E Warranty Viii Appendix D Specifications ViiAtto Technology, Inc PrefacePage Diamond Storage Array Product Overview Diamond Storage Array featuresScsi model Fibre Channel modelDiamond Storage Array Technical Overview Adxt Powers ATA to New LevelsATA Interface Engine AIE The interface to each Connect to Ethernet Installation InstructionsPhysical setup Set up the Ethernet connectionSet up RAID configuration Rack mount ComponentsFloor model Components Sliding shelf or tray type systems should never Physical Set UpSpaced rail pairs in some rackmount cabinets Rack mount cabinets with stationary shelf or trayGeneral instructions Manual configuration Connecting a Fibre Channel ArrayAutoconfiguration Fibre Channel connections Bits Connecting a Scsi ArrayTo connect a Scsi array Bus speed, MB/sec Bus width Max. bus lengths Max. deviceScsi connections Numbering conventions Determining Drive and Sled DesignationsPhysical numbering Logical numberingRAID Level 5 QuickRAID5 with a fully ExamplesUnique serial number for each LUN RAID Level 10 QuickRAID10 The QuickRAID10RS-232 port Accessing the ArrayCommand Line Interface Atto ExpressNAVSnmp Initiator Host Diamond Array In-band CLI Over the Fibre ChannelDetails Initiator/Host Diamond Storage Array Invalidparameterincdb will be returnedSerial Port Access Serial port access To use Snmp Ethernet Access Telnet and Snmp ProtocolsTo connect to the Ethernet port To use TelnetTraps are generated for the following situations Type SaveConfiguration restart to reboot the arrayNavigating ExpressNAV Atto ExpressNAV Browser-based InterfaceBrowser compatibility Opening an ExpressNAV sessionInformation Sidebar ExpressNAV Pages Rebuild ConfigurationClear Data Logical UnitsCommand Line Interface actions and responses Command Line Interface Use and GuidancePage Command Defaults Example Summary of CLI CommandsCommand Defaults Example General Use Commands General CLI commands Ethernet Commands TelnetUsername TelnetPasswordTelnetTimeout Fibre Channel Configuration Commands FcWWName FcPortInfoFcPortList FcPortNameSerialPortEcho Serial Port Configuration CommandsSerialPortBaudRate SerialPortHandshakeSerial port CLI commands Diagnostic Commands VirtualDriveInfo SledFaultLEDTemperature SMARTDataMinEnclTempAlrm Maintenance CommandsFcScsiBusyStatus MaxEnclTempAlrm Maintenance CLI commands Drive Configuration Commands QuickRAID0 DriveWipeIdeTransferRate LUNStateRAIDInterleave RestoreModePagesRAID5ClearData RAID5ClearDataStatusExamples, refer to Information Commands Results on RAID Level Configuring DrivesJbod Just a Bunch of Disks Enhancing performance InterleaveHot Spare sleds Jbod To set up the Jbod configurationJbod Sled-based versus disk-based RAID LevelLUNs virtual drive numbers To remove RAID Level 0 groupsPage Page To remove RAID groups To set up RAID Level 1 groupsType SaveConfiguration Type SaveConfiguration Storage ManagementType set QuickRAID 1 To set up RAID Level 1 with Hot Spare sledsTo set up one RAID Level 5 group with one Hot Spare sled Configuring a fully-populated arrayTo set up RAID Level 5 groups Type set QuickRAID5 2 Type SaveConfiguration Restart Type set QuickRAID5 1 Type SaveConfiguration RestartTo set up two RAID Level 5 groups with two Hot Spare sleds LUN Removing RAID groups Type set QuickRAID5 ALL Type SaveConfiguration RestartType set QuickRAID10 0 1 2 To set up RAID Level 10 groupsType set QuickRAID10 1 Type SaveConfiguration Restart To set up RAID Level 10 with Hot Spare sledsRebuilding RAID Configurations To synchronize mirrored drives manually Set AutoRebuild disabled saveconfiguration restartTo change the RAID Interleave parameter RAID Interleave ParametersRAID interleave Hardware Maintenance Maintenance Disk drives Hot Swap Operating InstructionsBlower assemblies Power suppliesTo replace a blower assembly Optional Hot Spare Sled Type set QuickRAID1 Type SaveConfiguration RestartVirtual Drive Hot Spare sleds To set up two RAID Level 5 groups with Hot Spare sledsCopying Drives ProcedureCopy drives Updating Firmware Updating firmware using the RS-232 serial portType put ....ima Cd c\diamond\flashSystem Monitoring and Reporting System fault LED and error codes Power supply monitoringNumber of blinks Command Line Interface messages TroubleshootingWindows 2000 special instructions Error messages Specific situations and suggestions Type FirmwareRestart If LUNs do not display on the hostTo return to Default settings Resetting DefaultsDefault Factory DefaultCommand Default Reset if default Reset during Chosen Fibre Channel FeatureDriveInfo sled ID drive ID Appendix B Information Commands ResultsV80DTESC Info allLunInfo LUNInfo LUNVirtualDriveInfo VirtualDriveInfo active planned Virtual Drive IDRadio and television interference Safety compliances EMC specificationsEnvironmental and physical Rack mount dimensionsFloor mount dimensions Contact Atto Technology, Inc Manufacturer limited warranty