Orion 2000 manual Installing the Software Drivers

Page 11

or surge protector.

5. You are now ready to install the software drivers.

Installing the Software Drivers

This section explains how to install the software drivers that your PC requires for the cable modem to operate.

Installing the Software Drivers in Windows 98 SE Operating System

CAUTION: You must install the drivers located on the CD that ships with your cable modem. If you use the default Windows-supplied software drivers, you will not be able to properly install the cable modem.

To install the cable modem software drivers using the Windows 98 operating system:

1.Power on your PC. After your computer boots, Windows detects the cable modem. The Found New Hardware screen appears, followed by the Add New Hardware Wizard screen.

User’ Guide

11

Image 11

Contents Orion Contents Mode of Operation Docsis Configuration File Vsif TAG Support Contact Your Local Cable Operator Understand the Cable Modem’s FeaturesBefore You Begin Not Supplied Prepare Your Area for Cable Modem InstallationGather Supplied and Required Items SuppliedInstalling the Software Drivers Before Hardware Connection Installing the Cable Modem Using the USB PortPage Page Installing the Hardware Installing the Software Drivers User’ Guide User’ Guide Page Page Page User’ Guide Page Page User’ Guide Page Page Page User’ Guide None of the LEDs is on when I power on the LAN Cable Modem Troubleshooting the USB InstallationSelect USB Composite Device and click Remove Click Refresh Uninstalling the USB Driver Installing the Modem Using the Ethernet PortEnet LED on my cable modem is not lit Troubleshooting the Ethernet InstallationNone of the LEDs are on when I power on the Cable Modem Cable Modem LEDs and Connectors LEDs on the Front of the Modem Connectors on the Back of the ModemPage Getting Help Telnet commandsCMshow ? CMshow interTab CMshow interface Redisplaying a commandDebug Ping ImagePassword CMshow version ¾ show dhcpCMshow dhcp ¾ show versionCMshow interface ethernet ¾ show interfaceCMshow interface ? ¾ show interface ethernetCMshow interface usb CMshow running-configuration¾ show interface usb Qpsk ¾ show downstream Display downstream information ¾ show cpe-info Display CPE information¾ show upstream ¾ show nat configCMshow nat config CMshow downstream¾ show user CMshow nat timer¾ show access-list ¾ show nat time¾ show cpe-limit CMshow access-list¾ show pppoe-forwarding Display PPPoE enable or disable ¾ nvram factory-defaultCM dhcp ip-pool add 192.168.100.2 CMshow dhcp CMtftp server¾ dhcp dns delete 1~4/all ¾ dhcp gateway ip address Set Dhcp gateway ip address ¾ dhcp ip-pool delete 1-20/allCMnat static ipmapping add 68.5.203.16 One to one mapping¾ nat static ipmapping delete index/all Port forwarding settingNAT static ip CMnat static ip disableCMnat static ip enable CMnat static portmapping deleteInterfaces ¾ interface cable startup ¾ interface ethernet startup¾ rip version 1/2/2b ¾ rip timer expire second Set routing entry expire timeCMrip key-chain 1 10 start-time 2002-4-20 ¾ rip defaultCMaccess-list 41 permit 00d0.5921.3354 ffff.ffff.ffff Web-access¾ reset ¾ access-list delete list IDall¾ pppoe-forwarding enabledisable Optional CMcopy tftpconfig 68.5.203.15 4ips.txt¾ quit Disconnect telnet ¾ ip nat enable Mode of OperationBridge mode NAT mode¾ ip route enable Routing mode¾ ip natroute enable NAT/Routing modeUser’ Guide Cable Modem Information Accessing the Web User InterfaceWeb User Interface Web User Interface HomeCable Modem Status Downstream Upstream Upstream Burst Operation Parameters Event Log Bridge Mode NAT/Router configurationSubmit NAT Mode Gateway LAN InterfaceReset WAN InterfaceRouter Mode Routing Protocol LAN Interface Delete Key ChainAdd Submit NAT Router Mode Routing Protocol Gateway LAN Interface Authentication mode Authentication Key Chain Submit Gateway LAN Setup Page Meaning Docsis configuration file Vsif tag support