Orion 2000 manual User’ Guide

Page 13

4.Check the CD-ROM drive check box and verify that the CD is in the CD-ROM drive. Click

Next to have Windows search for the necessary driver files. You will see the following

5.Select the updated driver (Recommended) Ambit USB Cable Modem and click next. You will see the following screen.

CAUTION: You must verify that Ambit USB Cable Modem appears on the screen. If USB Composite Device appears, you must click Back twice and specify the correct location of the driver files. DO NOT proceed if USB Composite Device is displayed in the above window. Contact your cable provider for further assistance.

User’ Guide

13

Image 13

Contents Orion Contents Mode of Operation Docsis Configuration File Vsif TAG Support Before You Begin Understand the Cable Modem’s FeaturesContact Your Local Cable Operator Gather Supplied and Required Items Prepare Your Area for Cable Modem InstallationSupplied Not SuppliedInstalling the Software Drivers Before Hardware Connection Installing the Cable Modem Using the USB PortPage Page Installing the Hardware Installing the Software Drivers User’ Guide User’ Guide Page Page Page User’ Guide Page Page User’ Guide Page Page Page User’ Guide None of the LEDs is on when I power on the LAN Cable Modem Troubleshooting the USB InstallationSelect USB Composite Device and click Remove Click Refresh Uninstalling the USB Driver Installing the Modem Using the Ethernet PortNone of the LEDs are on when I power on the Cable Modem Troubleshooting the Ethernet InstallationEnet LED on my cable modem is not lit Cable Modem LEDs and Connectors LEDs on the Front of the Modem Connectors on the Back of the ModemPage Getting Help Telnet commandsCMshow ? CMshow interTab CMshow interface Redisplaying a commandDebug Ping ImagePassword CMshow dhcp ¾ show dhcp¾ show version CMshow versionCMshow interface ? ¾ show interface¾ show interface ethernet CMshow interface ethernet¾ show interface usb CMshow running-configurationCMshow interface usb Qpsk ¾ show downstream Display downstream information ¾ show cpe-info Display CPE informationCMshow nat config ¾ show nat configCMshow downstream ¾ show upstream¾ show access-list CMshow nat timer¾ show nat time ¾ show user¾ show pppoe-forwarding Display PPPoE enable or disable CMshow access-list¾ nvram factory-default ¾ show cpe-limit¾ dhcp dns delete 1~4/all CMtftp serverCM dhcp ip-pool add 192.168.100.2 CMshow dhcp ¾ dhcp gateway ip address Set Dhcp gateway ip address ¾ dhcp ip-pool delete 1-20/allCMnat static ipmapping add 68.5.203.16 One to one mapping¾ nat static ipmapping delete index/all Port forwarding settingCMnat static ip enable CMnat static ip disableCMnat static portmapping delete NAT static ipInterfaces ¾ interface cable startup ¾ interface ethernet startup¾ rip version 1/2/2b ¾ rip timer expire second Set routing entry expire timeCMrip key-chain 1 10 start-time 2002-4-20 ¾ rip defaultCMaccess-list 41 permit 00d0.5921.3354 ffff.ffff.ffff Web-access¾ pppoe-forwarding enabledisable Optional ¾ access-list delete list IDallCMcopy tftpconfig 68.5.203.15 4ips.txt ¾ reset¾ quit Disconnect telnet Bridge mode Mode of OperationNAT mode ¾ ip nat enable¾ ip route enable Routing mode¾ ip natroute enable NAT/Routing modeUser’ Guide Web User Interface Accessing the Web User InterfaceWeb User Interface Home Cable Modem InformationCable Modem Status Downstream Upstream Upstream Burst Operation Parameters Event Log Bridge Mode NAT/Router configurationReset NAT Mode Gateway LAN InterfaceWAN Interface SubmitRouter Mode Routing Protocol LAN Interface Add Key ChainDelete Submit NAT Router Mode Routing Protocol Gateway LAN Interface Authentication mode Authentication Key Chain Submit Gateway LAN Setup Page Meaning Docsis configuration file Vsif tag support