Orion 2000 manual ¾ rip version 1/2/2b, ¾ rip timer expire second Set routing entry expire time

Page 52

IP

¾ip route {enable/disable}

Enable/disable routing with RIP. Default routing mode is RIPv2. Reference Mode of Operation section for example.

¾ip natroute {enable/disable}

Enable/disable NAT and routing function simultaneously. Reference Mode of Operation section for example.

¾ip nat {enable/disable} Enable/disable NAT/PAT function.

Reference Mode of Operation section for example.

RIP

¾rip version {1/2/2b}

Version number : 1 for RIPv1, 2 for RIPv2, 2b for RIPv2-broadcast mode

¾rip timer update {second} Set routing table update time

¾rip timer response {second}

Set interval between RIP response message send out

¾rip timer expire {second} Set routing entry expire time

Set garbage collection time

¾rip timer garbage {second} Set garbage collection time

¾rip timer default

User’ Guide

52

Image 52

Contents Orion Contents Mode of Operation Docsis Configuration File Vsif TAG Support Before You Begin Understand the Cable Modem’s FeaturesContact Your Local Cable Operator Prepare Your Area for Cable Modem Installation Gather Supplied and Required ItemsSupplied Not SuppliedInstalling the Cable Modem Using the USB Port Installing the Software Drivers Before Hardware ConnectionPage Page Installing the Hardware Installing the Software Drivers User’ Guide User’ Guide Page Page Page User’ Guide Page Page User’ Guide Page Page Page User’ Guide Troubleshooting the USB Installation None of the LEDs is on when I power on the LAN Cable ModemSelect USB Composite Device and click Remove Click Refresh Installing the Modem Using the Ethernet Port Uninstalling the USB DriverNone of the LEDs are on when I power on the Cable Modem Troubleshooting the Ethernet InstallationEnet LED on my cable modem is not lit Cable Modem LEDs and Connectors Connectors on the Back of the Modem LEDs on the Front of the ModemPage Telnet commands Getting HelpCMshow interTab CMshow interface Redisplaying a command CMshow ?Debug Image PingPassword ¾ show dhcp CMshow dhcp¾ show version CMshow version¾ show interface CMshow interface ?¾ show interface ethernet CMshow interface ethernet¾ show interface usb CMshow running-configurationCMshow interface usb Qpsk ¾ show cpe-info Display CPE information ¾ show downstream Display downstream information¾ show nat config CMshow nat configCMshow downstream ¾ show upstreamCMshow nat timer ¾ show access-list¾ show nat time ¾ show userCMshow access-list ¾ show pppoe-forwarding Display PPPoE enable or disable¾ nvram factory-default ¾ show cpe-limit¾ dhcp dns delete 1~4/all CMtftp serverCM dhcp ip-pool add 192.168.100.2 CMshow dhcp ¾ dhcp ip-pool delete 1-20/all ¾ dhcp gateway ip address Set Dhcp gateway ip addressOne to one mapping CMnat static ipmapping add 68.5.203.16Port forwarding setting ¾ nat static ipmapping delete index/allCMnat static ip disable CMnat static ip enableCMnat static portmapping delete NAT static ipInterfaces ¾ interface ethernet startup ¾ interface cable startup¾ rip timer expire second Set routing entry expire time ¾ rip version 1/2/2b¾ rip default CMrip key-chain 1 10 start-time 2002-4-20Web-access CMaccess-list 41 permit 00d0.5921.3354 ffff.ffff.ffff¾ access-list delete list IDall ¾ pppoe-forwarding enabledisable OptionalCMcopy tftpconfig 68.5.203.15 4ips.txt ¾ reset¾ quit Disconnect telnet Mode of Operation Bridge modeNAT mode ¾ ip nat enableRouting mode ¾ ip route enableNAT/Routing mode ¾ ip natroute enableUser’ Guide Accessing the Web User Interface Web User InterfaceWeb User Interface Home Cable Modem InformationCable Modem Status Downstream Upstream Upstream Burst Operation Parameters Event Log NAT/Router configuration Bridge ModeNAT Mode Gateway LAN Interface ResetWAN Interface SubmitRouter Mode Routing Protocol LAN Interface Add Key ChainDelete Submit NAT Router Mode Routing Protocol Gateway LAN Interface Authentication mode Authentication Key Chain Submit Gateway LAN Setup Page Docsis configuration file Vsif tag support Meaning