Moxa Technologies C168P user manual Speed

Page 20
Speed

3.Enter the CAP address of the C168P board to be configured.

4.Configure the following parameters as necessary.

Port Index Indicate the port index for each port.

I/O address Enter the base I/O address for each port, either sequentially or not. Avoid to conflicting with any other devices.

IRQ

Enter the IRQ, 2, 3, 4, 5, 7, 10, 11, 12 or 15, for each port,

 

independently or not.

Speed

This field specifies the use of normal or high speed capability.

 

Normal speed ranges from 50 bps to 115.2 Kbps. High speed

 

ranges from 50 bps to 921.6 Kbps. C168P support only normal

 

speed spectrum. In other word, it is not available for speed

 

faster than 115.2K bps.

2-6C168P User’s Manual

Image 20
Contents C168P User’s Manual May 1999 7th EditionUniversal 8 Port Serial Board support@moxa.com.twCopyright Notice TrademarksDisclaimer C168P User’s ManualMOXA Internet Services About This Manual Chapter 2 Hardware InstallationChapter 3 Software Installation Chapter 5 Connection Option Opt8x and Cable WiringHardware Installation Software InstallationSerial Programming Tools Table of ContentsTechnical Reference Connection Option Opt8x and Cable WiringTroubleshooting Overview The Standard Multiport Async SolutionsIntroduction Switch Quick InstallationHardware Configuration Method JumperIntroduction Operating System SupportMOXA Serial Comm Tools Wide ApplicationsFeatures Check List Opt8A/Opt8B/Opt8SOpt8C/Opt8D P1P2 P3 P4P5 P6 P7 P8 Opt8F/Opt8ZOpt8J RS-422/485 Port Switch of Opt8JRS-422 Mode Opt8JInstallation Guide RS-485 ModeC168P Hardware InstallationDefault Settings Quick Hardware Installation How to Do Quick Hardware InstallationHardware Installation with IO-IRQ Utility IO-IRQ Utility and Hardware Configuration 2-4 C168P User’s Manual2. Select “Smartio/Industio ISA Family” and press ENTER key Speed 5. Press F10 to save the configuration and exit the utility 2-8 C168P User’s Manual Software Installation Windows NTInstalling Driver 5. Select “MOXA Smartio/Industio Family multiport board” in the “Select OEM Option” dialog box, and then click OK to enter the “Moxa Smartio/Industio Configuration Panel” dialog box to start the installation 3-4 C168P User’s Manual Tx FIFO Size Port NumberRx FIFO Trigger 3-6 C168P User’s Manual Configuring Board and Port In this configuration panel, you may Removing Driver Windows 95/98Updating Driver 1. Run Setup95.exe in the driver diskette Note ! Go directly to the step 7 if you need not change any setting 3-12 C168P User’s Manual If error message like “Smartio C168 Series CAP=0x0180, port 1=COM3 3-14 C168P User’s Manual C168P User’s Manual 3-16 C168P User’s Manual Installing Driver Driver Setup 3-18 C168P User’s ManualSoftware Installation 3-20 C168P User’s Manual You may now enter/modify each port’s configuration. These displayed values are the port initial values as driver is loaded Loading Driver Unloading Driver 3-24 C168P User’s Manual Windows NT and Windows 95/98 InstallationSerial Programming Tools 4-2 C168P User’s Manual PComm Programming LibraryUtilities Diagnostic for MOXA boards only Monitor for MOXA boards under Windows NT Only 4-4 C168P User’s ManualTerminal Emulator 4-6 C168P User’s Manual DOS API-232 LibraryData Scope There are three major functions in Data Scope utility RS-485 Programming for Opt8J DiagnoseThere are 2 solutions to control RS-485 2-wire transmission Solution4-10 C168P User’s Manual RS-232 Cable Wiring for Opt8A/B/C/D/S Connection Option Opt8x and Cable WiringThe followings are pin assignments for various connection options Opt8A/S DCE, DB25 Female2 RxD 3 TxD 4 CTS 5 RTS 6 DTR 7 GND 8 DCD 20 DSR Opt8B/C DTE, DB25 MaleNull Modem Cable Opt8B/C Type 1 To connect C168P to a DTE deviceStraight-through Cable Opt8A/S Type 2 To connect C168P to a DCE device 5-4 C168P User’s ManualConnection Option Opt8x and Cable Wiring DTE Device 5-6 C168P User’s ManualOpt8A/S RS-422 Cable Wiring for Opt8J/F/Z RS-422 Pinouts for Opt8J/F/Z Opt8J/F/Z2 RxD+B 3 TxD+B 14 RxD-A 16 TxD-A 7 GND 4 CTS+B 5 RTS+B RTS-ARS-422 Point-to-point Opt8J/F/ZRS-422 Device RS-422 Device NRS-485 Cable Wiring for Opt8J Opt8JRS-422/485 Impedance Matching 5-12 C168P User’s Manual Troubleshooting General TroubleshootingHardware causes and solutions Hardware Causes and SolutionsSoftware Causes and Solutions Step Step Step Step Step Step A Io-irqStep 8. Power off the PC 3. The COM number of the C168P conflicts with others 4. Windows NT system panic blue screen6-6 C168P User’s Manual Appendix SpecificationsTechnical Reference A-2 C168P User’s Manual Device PC I/O Port Address MapIO/ Address DB62 Connector Pinouts SignalA-4 C168P User’s Manual Pin noProblem Report Form C168P 3. Moxa hardware settingsCustomer name Company Tel Fax EmailDate 1. Moxa Product C168P Serial Number 2. Moxa Driver VersionReturn Procedure