Moxa Technologies C168P user manual Switch, Quick Installation, Jumper, Smartio Family

Page 8
Hardware Configuration Method

Hardware Configuration Method

JP1

Switch

ON

1 2 3 4

Jumper

.........

.........

Smartio Family

Traditional

 

Multipoort Board

New : set I/O address and IRQ via software Utility.

Traditional : set switch and and jumper manually for I/O address and IRQ.

Instead of using traditional jumper or switch for IRQ and I/O address settings, hardware configuration of each port is easily set by DOS utility, Io-irq.exe, which reads and writes the on-board EEPROM for configuration information through the CAP (Configuration Access Port) address. The CAP address is the only channel via which the configuration utility Io-irq.exe can access the board, which is identical to the first port's base I/O address.

The only jumper, JP1, is designed in case that users forget the CAP address. Normally JP1 is left open. When JP1 is short, the CAP address is forced to a fixed I/O address, 0xA700. However, to adopt quick installation (described later), it is a must to keep JP1 always short.

Quick Installation

To ease the hardware configuration, users who install only one C168P board under Windows NT/95/98 are recommended to adopt quick installation described in Chapter 2.

Because the family is so flexible in hardware configuration that they are compatible virtually with all kinds of other manufacturer's multiport boards using 16450 or 16550 UART.

1-2C168P User’s Manual

Image 8
Contents C168P User’s Manual May 1999 7th EditionUniversal 8 Port Serial Board support@moxa.com.twCopyright Notice TrademarksDisclaimer C168P User’s ManualMOXA Internet Services About This Manual Chapter 2 Hardware InstallationChapter 3 Software Installation Chapter 5 Connection Option Opt8x and Cable WiringHardware Installation Software InstallationSerial Programming Tools Table of ContentsTechnical Reference Connection Option Opt8x and Cable WiringTroubleshooting Overview The Standard Multiport Async SolutionsIntroduction Switch Quick InstallationHardware Configuration Method JumperIntroduction Operating System SupportMOXA Serial Comm Tools Wide ApplicationsFeatures Check List Opt8A/Opt8B/Opt8SOpt8C/Opt8D P1P2 P3 P4P5 P6 P7 P8 Opt8F/Opt8ZOpt8J RS-422/485 Port Switch of Opt8JRS-422 Mode Opt8JInstallation Guide RS-485 ModeC168P Hardware InstallationDefault Settings Quick Hardware Installation How to Do Quick Hardware InstallationHardware Installation with IO-IRQ Utility IO-IRQ Utility and Hardware Configuration 2-4 C168P User’s Manual2. Select “Smartio/Industio ISA Family” and press ENTER key Speed 5. Press F10 to save the configuration and exit the utility 2-8 C168P User’s Manual Software Installation Windows NTInstalling Driver 5. Select “MOXA Smartio/Industio Family multiport board” in the “Select OEM Option” dialog box, and then click OK to enter the “Moxa Smartio/Industio Configuration Panel” dialog box to start the installation 3-4 C168P User’s Manual Tx FIFO Size Port NumberRx FIFO Trigger 3-6 C168P User’s Manual Configuring Board and Port In this configuration panel, you may Removing Driver Windows 95/98Updating Driver 1. Run Setup95.exe in the driver diskette Note ! Go directly to the step 7 if you need not change any setting 3-12 C168P User’s Manual If error message like “Smartio C168 Series CAP=0x0180, port 1=COM3 3-14 C168P User’s Manual C168P User’s Manual 3-16 C168P User’s Manual Installing Driver Driver Setup 3-18 C168P User’s ManualSoftware Installation 3-20 C168P User’s Manual You may now enter/modify each port’s configuration. These displayed values are the port initial values as driver is loaded Loading Driver Unloading Driver 3-24 C168P User’s Manual Windows NT and Windows 95/98 InstallationSerial Programming Tools 4-2 C168P User’s Manual PComm Programming LibraryUtilities Diagnostic for MOXA boards only Monitor for MOXA boards under Windows NT Only 4-4 C168P User’s ManualTerminal Emulator 4-6 C168P User’s Manual DOS API-232 LibraryData Scope There are three major functions in Data Scope utility RS-485 Programming for Opt8J DiagnoseThere are 2 solutions to control RS-485 2-wire transmission Solution4-10 C168P User’s Manual RS-232 Cable Wiring for Opt8A/B/C/D/S Connection Option Opt8x and Cable WiringThe followings are pin assignments for various connection options Opt8A/S DCE, DB25 Female2 RxD 3 TxD 4 CTS 5 RTS 6 DTR 7 GND 8 DCD 20 DSR Opt8B/C DTE, DB25 MaleNull Modem Cable Opt8B/C Type 1 To connect C168P to a DTE deviceStraight-through Cable Opt8A/S Type 2 To connect C168P to a DCE device 5-4 C168P User’s ManualConnection Option Opt8x and Cable Wiring DTE Device 5-6 C168P User’s ManualOpt8A/S RS-422 Cable Wiring for Opt8J/F/Z RS-422 Pinouts for Opt8J/F/Z Opt8J/F/Z2 RxD+B 3 TxD+B 14 RxD-A 16 TxD-A 7 GND 4 CTS+B 5 RTS+B RTS-ARS-422 Point-to-point Opt8J/F/ZRS-422 Device RS-422 Device NRS-485 Cable Wiring for Opt8J Opt8JRS-422/485 Impedance Matching 5-12 C168P User’s Manual Troubleshooting General TroubleshootingHardware causes and solutions Hardware Causes and SolutionsSoftware Causes and Solutions Step Step Step Step Step Step A Io-irqStep 8. Power off the PC 3. The COM number of the C168P conflicts with others 4. Windows NT system panic blue screen6-6 C168P User’s Manual Appendix SpecificationsTechnical Reference A-2 C168P User’s Manual Device PC I/O Port Address MapIO/ Address DB62 Connector Pinouts SignalA-4 C168P User’s Manual Pin noProblem Report Form C168P 3. Moxa hardware settingsCustomer name Company Tel Fax EmailDate 1. Moxa Product C168P Serial Number 2. Moxa Driver VersionReturn Procedure