Schneider Electric TSXETG100 manual Slave Mode Device List Setup, Slave Mode Topology, RS485

Page 9

63230-319-211A1

ConneXiumEthernet Gateway

2/2006

 

Setup

 

 

Slave Mode Device List Setup

Serial port slave mode allows serial Modbus master devices to access

 

 

information from serial slave devices across a TCP/IP network. Figure 6

 

 

below illustrates how the devices are connected using the device list

 

 

settings in Figure 7.

Figure 6:

Slave Mode Topology

 

ENGLISH

 

Ethernet

 

 

Connection

 

 

 

ETG in

ETG in master

ETG in

slave mode

 

mode

master mode

 

IP address:

IP address:

 

169.254.0.28

169.254.0.75

 

 

 

RS232 or RS485

RS485

RS485

connection

connection

connection

 

Up to 16 remote IP connections with up to 128 serial slave devices are possible

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2

 

5

 

 

2

 

3

 

 

4

 

 

5

 

 

6

 

7

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Serial Slave Devices

 

 

 

 

 

Serial Slave Devices

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

If you selected Slave mode on the Serial Port page, follow the steps below

 

 

 

 

 

 

 

 

to set up the device list:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Action

 

 

 

 

 

 

 

 

Result

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1.

From the Setup page, click Device List.

Opens the Device List page.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2.

Select the number of viewable devices (1 to

Selects the number of viewable locations that

 

 

 

 

 

 

 

 

 

128), then click Apply.

 

 

 

 

 

 

 

can be used to define remote Modbus TCP/IP

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

devices.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3.

In the Local ID text box, type the local ID

Enters the address of the device that the local

 

 

 

 

 

 

 

 

 

(address) of the serial slave device.

 

 

 

Modbus master device will use to access the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

remote device.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4.

In the Remote ID text box, type the remote

Enters the serial slave address of the remotely

 

 

 

 

 

 

 

 

 

ID (address) of the serial slave device.

connected device.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5.

Select the Connection.

 

 

 

 

 

 

 

Selects the Modbus TCP/IP address to

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

associate with the remote ID.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6.

Repeat steps 3 through 5 until all of the

Enters all of the mapping information for the

 

 

 

 

 

 

 

 

 

devices are entered.

 

 

 

 

 

 

 

ETG to communicate to the remote devices.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

7.

Click Apply.

 

 

 

 

 

 

 

Updates the Device List settings.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Figure 7: Device List Page in Slave Mode

© 2006 Schneider Electric. All Rights Reserved.

9

Image 9
Contents ConneXium Ethernet Gateway TSXETG100 Table of ContentsIntroduction Address Resolution Protocol ARP ARP is used to convert IPSupported Ethernet Protocols HardwareAdditional Resources Accessing the ETG Over a NetworkLogging into the ETG Logging OutDiagnostics SetupETG User Interface Overview ETG static web pagesEthernet and TCP/IP Settings Setup63230-319-211A1 ConneXium Ethernet Gateway 2006 Setup Option Description SettingScenario Duplicate IP Detected Power/Status LED ConneXium Ethernet Gateway 63230-319-211A1 Setup 2006Duplicate IP Address Detection Duplicate IP Detection ScenariosDefault Master 2006 SetupDefault Even Default 3 secondsMaster Mode Device List Setup Master Mode Topology For master mode usage of the COM portDevice List Before you begin, keep in mind the followingSlave Mode Topology Slave Mode Device List SetupEthernet Connection ETG RS485ConneXium Ethernet Gateway Setup ETG accounts and passwordsAccount Default Password User AccountsGroup Access Web Page AccessGroup Access AccessModbus TCP/IP Filtering TCP/IP Filtering Check Enable FilteringParameters Snmp ParametersConneXium Ethernet Gateway 63230-319-211A1 Diagnostics 2006 DiagnosticsStatistics Menu barInterpreting Statistics 2006 DiagnosticsStatistic Description EthernetConneXium Ethernet Gateway Diagnostics Serial PortGateway Information ETG Read Device Register Settings Option Description DefaultRead Device Registers Finding the Firmware Version FirmwareGetting New Firmware Updating the Firmware FileDeutsch
Related manuals
Manual 2 pages 58.14 Kb