Network Technologies CAT5 operation manual Alternate OSD Key, Alternate OSD screen

Page 35

Alternate OSD Key

This function enables the administrator to assign a key in addition to the <`> (accent key) to use with <Ctrl> to enter into OSD Command Mode. The default factory setting for this option is <0> (disabling the option).

To assign an Alternate OSD key press <K> from the Administration Menu. (From Command Mode type <A>-<K>.)

A window will open displaying the current "Cur" value, the range of values (from 4 to 164), and a place for the new value to be assigned. As the administrator changes the value, the corresponding keyboard key will appear next to it in parenthesis. Enter the value "0" to disable the feature.

Function

Keystroke

Press key to enter directly

P <x>

 

x= any key on the

 

keyboard

Increment value by 1

Up arrow

 

 

Decrement value by 1

Down Arrow

 

 

Increment value by 10

Page Up

 

 

 

Decrement value by 10

Page Down

 

 

Insert minimum value

Home

 

 

Insert maximum value

End

 

 

Save new value

S or Enter

 

 

Disable feature (input value 0)

D

 

 

Esc

X or Esc

 

 

Figure 37- Alternate OSD screen

After pressing <S> to save or <D> to disable, the new value will replace the "Cur. Value" as the current value. This function effects all users of the segment..

FYI: The Alternate Command Hot Key does not replace the <`> (accent) key, it just works as an additional way to enter into Command Mode. After setting it, the user can enter into Command Mode either with <Ctrl> + <`> or with <Ctrl> + <Alternative Command Hot Key> combination. To disable it, the administrator should set the new value at 0 or press <D>.

31

Image 35
Contents Primux Trademark Table of Contents Typical Application Warranty InformationMaterials IntroductionNTI Features and FunctionsDefinitions Preparation for InstallationHost Adapter InstallationInstallation of a PS/2 CPU CPU Installation of a USB CPUInstallation of a SUN CPU User Station Connecting the CAT5 cable to the Host AdapterInstallation with PS/2 devices RearViewof PRIMUX-UZRUserStation Installation with USB devicesRearViewofPRIMUX-UZRUserStation Connecting the CAT5 cable to the User StationPower Up for the first time USB HA-USB SUN HA-SUN Daisy-Chained Host AdaptersAdding a Host Adapter to a segment HA-PS2Initial Startup Using the Primux CAT5 KVM SwitchUser Rights vs. Administrator Rights Hot PluggingQuick Connect Change the Default Administrator PasswordAdministrator Login and Password Setup Host AdaptersSecurity Standards of OperationKeypad Control User Login User Access FunctionsAdministrator Login AutologinFunction Enter Administration Mode Administrator only- seeNormal Mode Scan ModeFunction Description Settings MenuFunction Keystroke Value or Action Find Host AdapterHost Adapter Info screen Help Pages OSD Settings MenuFunction Description Keystroke Host Adapters for ScanChange Scan Dwell Time Video Quality AdjustmentAdministration Menu AdministrationHost Adapter List Edit Hosts, Users, and User Station InfoFunction Keystroke Confirmation Parameter Value Required Edit Host AdapterUser List User ListEdit User User InfoFunction Keystroke Parameter Value Add New UserHost Access List Edit User PasswordEdit User Station Change Administrators PasswordSelect Autologon User Use with care, all user configuration Settings will be lostUser Station Info screen Idle TimeoutAlternate OSD screen Alternate OSD KeyFunction Description Keystroke Confirmation Required Update Firmware/Bootloader MenuAcquire/Send DDC Info Configure MAC Host AdaptersSelect Keyboard Language menu Select Keyboard LanguageDistance feet Technical SpecificationsInterconnection Cable Wiring Method Pin Wire Color Pair FunctionCTS RTS DSR DTR DCD Mating Face 25D Male Connector Female ConnectorNull Modem Cable Pinouts Function Source Keystroke Sequence Safety and EMC Regulatory StatementsMenu QUICK-FIND Keystroke Table Warranty Information