Sun Microsystems LSI22320-SR manual Installing the Host Adapter

Page 13

512K bytes of Flash ROM for booting in a Sun SPARC or a Sun Solaris x86 OS processor-based host system

A 64-bit universal type board edge connector that provides:

64-bit, 133-MHz PCI-X interface compatibility

32-bit/64-bit PCI interface backwards compatibility

Installing the Host Adapter

Before you start, read these instructions, and also read the installation instructions in the documentation that applies to the storage device(s) to be connected to the host adapter. Also, before installing the host adapter, read the Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Release Notes for required information, including lists of supported cables and storage devices. Downloading the release notes is described in “To Access the Release Notes” on page viii

Caution – This host adapter is only for connection to a single-ended (SE) or low-

!voltage differential (LVD) device, and it does not work if connected to a high-voltage differential (HVD) device.

Caution – Damage to the HBA can occur as the result of careless handling or electrostatic discharge (ESD). Always handle the HBA with care to avoid damage to electrostatic sensitive components.

To minimize the possibility of ESD-related damage, Sun strongly recommends using both a workstation antistatic mat and an ESD wrist strap. You can get an ESD wrist strap from any reputable electronics store or from Sun as part number #250-1007.

Observe the following precautions to avoid ESD-related problems:

Leave the HBA in its antistatic bag until you are ready to install it in the system.

Always use a properly fitted and grounded wrist strap or other suitable ESD protection when handling the HBA and observe proper ESD grounding techniques.

Hold the HBA by the edge of the PCB or mounting bracket, not the connectors.

Place the HBA on a properly grounded antistatic work surface pad when it is out of its protective antistatic bag.

Chapter 1 Installing, Connecting, and Testing the Host Adapter 3

Image 13
Contents Sun Microsystems, Inc Please Recycle Contents Specifications Before You Read This Book PrefaceHow This Book Is Organized Using Unix CommandsRelated Documentation Typographic ConventionsTo Access the Release Notes Accessing Sun DocumentationRight frame, under Use, click Documentation Contacting Sun Technical Support Third-Party Web SitesSun Welcomes Your Comments Page Installing, Connecting, and Testing the Host Adapter 1Sun StorEdge PCI/PCI-X Dual Ultra320 Scsi Host Adapter FeaturesInstalling the Host Adapter Install any required driver patches on the host To Prepare for Hardware InstallationInstall the SunVTS software on the host Exit the operating environmentChoose a PCI-X or PCI slot for installing the host adapter Unpack the host adapter Open the system To Install the Host AdapterRemove the filler panel for the desired slot Remove the wrist strap Close the systemConnecting the Host Adapter To Test the Installation Using the probe-scsi- all Command Testing the Host AdapterAs superuser, open the SunVTS window To Test the Installation With the SunVTS SoftwareBooting the Host Adapter Page Target Devices Ultra320 Scsi ConfigurationTable A-1Bus Restrictions Bus LengthCabling Cabling and TerminationTermination LVD LVD/MSE HVD Scsi SymbolsPhysical Dimensions SpecificationsPerformance Specifications Power RequirementsPCI Edge Connector Pin Definitions Trst Vhdci Connector Internal Scsi Connector Scsi Connector Pin Definitions+ATN P E N D I X C Declaration of Conformity Appendix C Declaration of Conformity FCC Class a Notice Regulatory Compliance StatementsSymbols Safety Agency Compliance StatementsPlacement of a Sun Product Noise Level Modifications to EquipmentBattery Warning Power Cord ConnectionSelv Compliance System Unit CoverRack System Warning SymbolesLaser Compliance Notice CD and DVD DevicesConformité Selv Modification du matérielConnexion du cordon d’alimentation Avis de conformité des appareils laser Mise en garde relative aux batteries Couvercle de lunitéMise en garde relative au système en rack Périphériques CD et DVDSicherheitsvorkehrungen SymboleModifikationen des Geräts Aufstellung von Sun-GerätenWarnung bezüglich Batterien Anschluss des NetzkabelsGehäuseabdeckung Warnungen bezüglich in Racks eingebauter SystemeCD- und DVD-Geräte Hinweis zur Laser-KonformitätMedidas de seguridad SímbolosColocación de un producto Sun Modificaciones en el equipoNivel de ruido Cumplimiento de la normativa para instalaciones SelvAdvertencia sobre el sistema en bastidor Advertencia sobre las bateríasCubierta de la unidad del sistema Norge Sverige Dispositivos de CD y DVDDanmark Suomi