Sun Microsystems LSI22320-SR manual Safety Agency Compliance Statements, Symbols

Page 37

Safety Agency Compliance Statements

Read this section before beginning any procedure. The following text provides safety precautions to follow when installing a Sun Microsystems product.

Safety Precautions

For your protection, observe the following safety precautions when setting up your equipment:

Follow all cautions and instructions marked on the equipment.

Ensure that the voltage and frequency of your power source match the voltage and frequency inscribed on the equipment’s electrical rating label.

Never push objects of any kind through openings in the equipment. Dangerous voltages may be present. Conductive foreign objects could produce a short circuit that could cause fire, electric shock, or damage to your equipment.

Symbols

The following symbols may appear in this book:

Caution – There is a risk of personal injury and equipment damage. Follow the instructions.

Caution – Hot surface. Avoid contact. Surfaces are hot and may cause personal injury if touched.

Caution – Hazardous voltages are present. To reduce the risk of electric shock and danger to personal health, follow the instructions.

Depending on the type of power switch your device has, one of the following symbols may be used:

On – Applies AC power to the system.

Off – Removes AC power from the system.

Standby – The On/Standby switch is in the standby position.

Modifications to Equipment

Do not make mechanical or electrical modifications to the equipment. Sun Microsystems is not responsible for regulatory compliance of a modified Sun product.

Placement of a Sun Product

Caution – Do not block or cover the openings of your Sun product. Never place a Sun product near a radiator or heat register. Failure to follow these guidelines can cause overheating and affect the reliability of your Sun product.

Noise Level

In compliance with the requirements defined in DIN 45635 Part 1000, the workplace-dependent noise level of this product is less than 70 db(A).

Appendix C Declaration of Conformity, Regulatory, and Safety Information 27

Image 37
Contents Sun Microsystems, Inc Please Recycle Contents Specifications Before You Read This Book PrefaceHow This Book Is Organized Using Unix CommandsRelated Documentation Typographic ConventionsTo Access the Release Notes Accessing Sun DocumentationRight frame, under Use, click Documentation Contacting Sun Technical Support Third-Party Web SitesSun Welcomes Your Comments Page Installing, Connecting, and Testing the Host Adapter 1Sun StorEdge PCI/PCI-X Dual Ultra320 Scsi Host Adapter FeaturesInstalling the Host Adapter Install any required driver patches on the host To Prepare for Hardware InstallationInstall the SunVTS software on the host Exit the operating environmentChoose a PCI-X or PCI slot for installing the host adapter Unpack the host adapter Open the system To Install the Host AdapterRemove the filler panel for the desired slot Remove the wrist strap Close the systemConnecting the Host Adapter To Test the Installation Using the probe-scsi- all Command Testing the Host AdapterAs superuser, open the SunVTS window To Test the Installation With the SunVTS SoftwareBooting the Host Adapter Page Target Devices Ultra320 Scsi ConfigurationTable A-1Bus Restrictions Bus LengthCabling Cabling and TerminationTermination LVD LVD/MSE HVD Scsi SymbolsPhysical Dimensions SpecificationsPerformance Specifications Power RequirementsPCI Edge Connector Pin Definitions Trst Vhdci Connector Internal Scsi Connector Scsi Connector Pin Definitions+ATN P E N D I X C Declaration of Conformity Appendix C Declaration of Conformity FCC Class a Notice Regulatory Compliance StatementsSymbols Safety Agency Compliance StatementsPlacement of a Sun Product Noise Level Modifications to EquipmentBattery Warning Power Cord ConnectionSelv Compliance System Unit CoverRack System Warning SymbolesLaser Compliance Notice CD and DVD DevicesConformité Selv Modification du matérielConnexion du cordon d’alimentation Avis de conformité des appareils laser Mise en garde relative aux batteries Couvercle de lunitéMise en garde relative au système en rack Périphériques CD et DVDSicherheitsvorkehrungen SymboleModifikationen des Geräts Aufstellung von Sun-GerätenWarnung bezüglich Batterien Anschluss des NetzkabelsGehäuseabdeckung Warnungen bezüglich in Racks eingebauter SystemeCD- und DVD-Geräte Hinweis zur Laser-KonformitätMedidas de seguridad SímbolosColocación de un producto Sun Modificaciones en el equipoNivel de ruido Cumplimiento de la normativa para instalaciones SelvAdvertencia sobre el sistema en bastidor Advertencia sobre las bateríasCubierta de la unidad del sistema Norge Sverige Dispositivos de CD y DVDDanmark Suomi